21 open source boards using the TCA9534PWR
Real designs built with the TCA9534PWR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
EEZ BB3 CM4 R1B0
intergalaktik
249.5 × 95 mm240 parts4LCustom license35D1600e psu breakout
antmicro
100 × 100 mm166 parts4LApache-2.020ESP32
PocketLab-Card
Jebroa77485.6 × 54 mm250 parts4LNo license2I2C-LCD-driver board hardware design
SolderedElectronics
54 × 22 mm32 parts2LTAPR-OHL-1.02RP2040/RP2350
Tool power supply
UBC-Hacker-Fab
90 × 160 mm121 parts4LNo license1RP2040/RP2350
Buslab
tombueng
160 × 100 mm414 parts6LCustom license0LoRa Pinze Sent
ISS-Lab-Unibo
107 × 51 mm212 parts6LNo license0Ito controller
luciddreams
160 × 110 mm202 parts4LNo license0Airgrep
mp911de
105 × 95 mm175 parts4LNo license0ESP32
Atlas carrier ctrl
md-sazzad-eee
130 × 100 mm145 parts4LNo license0ESP32
Waypoint
M-Mrk
140 × 80 mm129 parts4LNo license0Soldered easyC-LCD-Driver hardware design
test-gh-syncer2
22 × 54 mm32 parts2LTAPR-OHL-1.00Soldered-I2C-LCD-driver board hardware design
test-gh-syncer2
22 × 54 mm32 parts2LTAPR-OHL-1.00I2C-LCD-adapter hardware design
SolderedElectronics
54 × 22 mm32 parts2LTAPR-OHL-1.00ESP32
PocketLab-Card pcba routing wip
Jebroa77485.6 × 54 mm246 parts4LNo license2Front panel reva
itorralbo
184 × 62.3 mm42 parts2LMIT0ESP32
PocketLab-Card routing working
Jebroa77485.6 × 54 mm243 parts4LNo license2EEZ DIB B3C
eez-open
110 × 90 mm30 parts2LTAPR-OHL-1.0394EEZ DIB BP3C r3B3
intergalaktik
110 × 90 mm60 parts4LCustom license35Carrier
kkrzysztofik
90 × 60 mm43 parts2LMIT0Carrier tme
kkrzysztofik
90 × 60 mm42 parts2LMIT0
How designs wire the TCA9534PWR
Read from the KiCad layouts of 17 open source designs, one per repository: what each pin of the TCA9534PWR connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 14 of 17 designs, most often 100 nF (then 1 µF).
- The SCL pin has a pull-up to 3.3V on 11 of 17 designs, most often 4.7 kΩ (then 1.5 kΩ).
- The SDA pin has a pull-up to 3.3V on 11 of 17 designs, most often 4.7 kΩ (then 1.5 kΩ).
- The A1 pin is tied to GND on 12 of 17 designs (a signal on 5).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| A1pin 2 | Connected to: GND 71% · a signal 29% | — |
| A2pin 3 | Connected to: GND 71% · a signal 29% | — |
| P0pin 4 | Connected to: Signal 100% |
|
| P1pin 5 | Connected to: Signal 100% |
|
| P2pin 6 | Connected to: Signal 100% |
|
| P3pin 7 | Connected to: Signal 100% |
|
| GNDpin 8 | Connected to: GND 100% | — |
| INTpin 13 | Connected to: Not connected 71% · a signal 29% | — |
| SCLpin 14 | Connected to: The microcontroller 24%, a connector 24%, NMOS-DUAL 24% |
|
| SDApin 15 | Connected to: The microcontroller 24%, a connector 24%, NMOS-DUAL 24% |
|
| VCCpin 16 | Connected to: 3.3V 88% |
|
5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EEZ DIB B3C by eez-open, EEZ BB3 CM4 R1B0 by intergalaktik, D1600e psu breakout by antmicro and PocketLab-Card by Jebroa774.
The TCA9534PWR in open source designs
The gallery holds 21 open source boards using the TCA9534PWR from 17 GitHub repositories; a typical one measures about 100 × 62.3 mm and carries around 129 components.
62% use four copper layers or more, and 43% carry an open source license.
The most starred is EEZ DIB B3C by eez-open.
Parts used alongside the TCA9534PWR
Microcontrollers on boards using the TCA9534PWR
What boards using the TCA9534PWR are built for
TCA9534PWR: common questions
Where can I find a TCA9534PWR reference design?
Each of the 21 boards on this page is a real design using the TCA9534PWR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the TCA9534PWR VCC pin?
The VCC pin has a decoupling capacitor on 14 of 17 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 17 open source designs using the TCA9534PWR.
What pull-up resistor is used on the TCA9534PWR SCL pin?
The SCL pin has a pull-up to 3.3V on 11 of 17 designs, most often 4.7 kΩ (then 1.5 kΩ). Counted from the KiCad layouts of 17 open source designs using the TCA9534PWR.
What pull-up resistor is used on the TCA9534PWR SDA pin?
The SDA pin has a pull-up to 3.3V on 11 of 17 designs, most often 4.7 kΩ (then 1.5 kΩ). Counted from the KiCad layouts of 17 open source designs using the TCA9534PWR.
What parts are used alongside the TCA9534PWR?
The NMOS-DUAL, TPS613222A, USBLC6-2SC6, INA226AIDGSR and MAX17048G+T10 appear in the most repositories here.
Which microcontrollers do boards using the TCA9534PWR use?
Most are built on ESP32 (5), RP2040/RP2350 (2) and STM32 (1).
How big is a typical board using the TCA9534PWR?
The median is 100 × 62.3 mm, and 38% are two-layer designs.
What is the most popular open source board using the TCA9534PWR?
By GitHub stars, EEZ DIB B3C by eez-open, with 394 stars.
Can I simulate one of these boards using the TCA9534PWR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.