Main

VeeT23·SPECTRAL·hardware/main_board/main.kicad_pcb

Main PCB layout, top view — open source ESP32 board by VeeT23

About the Main PCB

Main is an open source ESP32 PCB design by VeeT23, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 60 × 40 mm, with 52 components from 26 distinct parts.

Its main chip is the ESP32-WROOM-32UE_M113EH6400UH3Q0_, from the ESP32 family. Other key parts include the ATA6561-GAQW-N. By type, the board carries 18 resistors, 13 capacitors, 12 connectors, 2 ICs, 2 transistors and 2 switches.

It belongs with the robotics & motion, sensors and displays & leds designs in this gallery.

From the project

Performance line following robot submitted to Southwork Robotics 2026

Short description of the embedded system and what it does.

SPECTRAL is a performance line following robot

- Platform: Espressif32 - MCU: ESP32-WROOM-32UE - Framework: Arduino - Build System: PlatformIO - IDE: Visual Studio Code + PlatformIO

The following CAN command IDs are used to communicate with the ODrive motor controller:

Spectral uses a 450 mAh 3s 75C lipo Running power is unknown however the circuit supports up to 10A continous. Idle power is measured to be ~140ma

Main components on the Main

Main bill of materials (BOM)

52 components, 26 distinct parts.

QtyPartRefs
1
ESP32-WROOM-32UE_M113EH6400UH3Q0_
U1
1
ATA6561-GAQW-N
U2
2
BSS138
Q1, Q4
1
Sensor 1
J1
1
Sensor 2
J2
1
Sensor 3
J3
1
Sensor 4
J4
1
Sensor 5
J5
1
CAN
J6
1
IMU
J7
1
OLED
J8
1
Power
J9
1
UART
J10
1
PWM
J11
1
NEOPIXEL
J12
1
Buzzer
BZ1
1
BOOT
SW1
1
RESET
SW2
1
GND
TP5
1
RED
D1
Show 6 more
QtyPartRefs
3
0.1uf
C1, C8, C10
3
10uf
C2, C9, C11
5
1nf
C3, C4, C5, C6, C7
2
100uf
C12, C13
9
4.7K
R1, R2, R8, R9, R10, R11, R12, R13 +1
9
100
R3, R4, R5, R6, R7, R15, R16, R17 +1

Main design files

The KiCad project lives in the VeeT23/SPECTRAL repository on GitHub; these links point at the commit this page was built from.

Main: common questions

What microcontroller does the Main use?

The Main is built around the ESP32-WROOM-32UE_M113EH6400UH3Q0_, from the ESP32 family.

How big is the Main PCB?

The Main measures 60 × 40 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Main?

52 components, from 26 distinct parts. The full bill of materials is listed on this page.

Where can I download the Main design files?

From the VeeT23/SPECTRAL repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Main design in my own project?

Yes, under the terms of its GPL-3.0 license, which VeeT23 chose for the repository.

Can I test firmware for the Main without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in SPECTRAL

Similar boards