Esp32s3 mic preamp
visweshvaras·MotoPulse
About the Esp32s3 mic preamp PCB
Esp32s3 mic preamp is an open source ESP32 PCB design by visweshvaras, published on GitHub. It is a 2-layer board measuring 62 × 40 mm, with 15 components from 12 distinct parts.
Its main chip is the ESP32-S3_Header, from the ESP32 family. Other key parts include the LM358. By type, the board carries 6 resistors, 5 capacitors, 2 connectors, 1 IC and 1 microphone.
It belongs with the audio, displays & leds and dev boards & breakouts designs in this gallery.
From the project
An Edge AI acoustic monitoring system powered by the ESP32-S3 (N16R8), INMP441 Digital I2S MEMS Microphone, and a 0.96" SSD1306 OLED Display.
An Edge AI acoustic monitoring system powered by the ESP32-S3 (N16R8), INMP441 Digital I2S MEMS Microphone, and a 0.96" SSD1306 OLED Display.
Built for automotive failure prediction (engine knocking, bearing wear, valve ticking, belt slippage) and industrial machinery health monitoring.
1. Digital Audio Acquisition (INMP441 I2S): - High-fidelity 16 kHz 16-bit PCM digital streaming via native ESP32-S3 I2S interface. - Eliminates analog breadboard noise, split-rail saturation, and component tolerances. 2. 16-Band Real-Time OLED Spectrum Analyzer: - On-device 64-point Integer Discrete Fourier…
Main components on the Esp32s3 mic preamp
Esp32s3 mic preamp bill of materials (BOM)
15 components, 12 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM358 | DIP-8_W7.62mm | U1 |
| 1 | ESP32-S3_Header | PinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | MIC_EXT | PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | MIC_ELECTRET | PinHeader_1x02_P2.54mm_Vertical | MK1 |
| 1 | 1µF | C_Rect_L7.0mm_W2.5mm_P5.00mm | C1 |
| 1 | 10µF (DNP) | CP_Radial_D5.0mm_P2.00mm | C2 |
| 1 | 10µF | CP_Radial_D5.0mm_P2.00mm | C3 |
| 1 | 10nF | C_Disc_D5.0mm_W2.5mm_P2.50mm | C4 |
| 1 | 100nF | C_Disc_D5.0mm_W2.5mm_P2.50mm | C5 |
| 1 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 3 | 100k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R3, R4 |
| 2 | 1k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R5, R6 |
Esp32s3 mic preamp design files
The KiCad project lives in the visweshvaras/MotoPulse repository on GitHub; these links point at the commit this page was built from.
Esp32s3 mic preamp: common questions
What microcontroller does the Esp32s3 mic preamp use?
The Esp32s3 mic preamp is built around the ESP32-S3_Header, from the ESP32 family.
How big is the Esp32s3 mic preamp PCB?
The Esp32s3 mic preamp measures 62 × 40 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32s3 mic preamp?
15 components, from 12 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Esp32s3 mic preamp design files?
From the visweshvaras/MotoPulse repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Esp32s3 mic preamp design in my own project?
The repository has no license, so all rights stay with visweshvaras. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Esp32s3 mic preamp without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in MotoPulse
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k