PSUtap digital
WEEE-Open·psutap·PSUtap_digital/PSUtap_digital.kicad_pcb
About the PSUtap digital PCB
PSUtap digital is an open source AVR/Arduino PCB design by WEEE-Open, published on GitHub under the CERN-OHL-W-2.0 license. It is a 2-layer board measuring 92 × 70.1 mm, with 80 components from 42 distinct parts.
Its main chip is the ATmega328P-AU, from the AVR/Arduino family. Other key parts include the LT1512, BQ2973, Si6926ADQ, CH340G and LTC3525-5. By type, the board carries 28 capacitors, 24 resistors, 7 switches, 6 ICs, 5 diodes and 4 connectors.
It belongs with the power & battery and usb & debug tools designs in this gallery.
From the project
Device for PSU power lines inspection and monitoring
The three are connected through male/female headers and communicate through an SPI interface.
Main components on the PSUtap digital
PSUtap digital bill of materials (BOM)
80 components, 42 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LT1512 | SO-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | BQ2973 | WSON-6_1.5x1.5mm_P0.5mm | U2 |
| 1 | Si6926ADQ | TSSOP-8_4.4x3mm_P0.65mm | U3 |
| 1 | CH340G | SOIC-16_3.9x9.9mm_P1.27mm | U4 |
| 1 | ATmega328P-AU | TQFP-32_7x7mm_P0.8mm | U5 |
| 1 | LTC3525-5 | SOT-363_SC-70-6 | U6 |
| 1 | 12MHz | Crystal_SMD_5032-2Pin_5.0x3.2mm | Y1 |
| 1 | 16MHz | Crystal_SMD_5032-2Pin_5.0x3.2mm | Y2 |
| 1 | USB_B_Micro | USB_Micro-B_Molex-105017-0001 | J1 |
| 1 | ADC_board_SPI | PinHeader_1x12_P2.54mm_Vertical | J2 |
| 1 | SD_card_SPI | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | Screen_SPI | PinHeader_1x14_P2.54mm_Vertical | J4 |
| 1 | Battery_Cell | PinHeader_1x02_P2.54mm_Vertical | BT1 |
| 1 | 231.8k | TRIM_3362P-1-304 | RV1 |
| 1 | Up | SW_PUSH_6mm | SW1 |
| 1 | Down | SW_PUSH_6mm | SW2 |
| 1 | Left | SW_PUSH_6mm | SW3 |
| 1 | Right | SW_PUSH_6mm | SW4 |
| 1 | B | SW_PUSH_6mm | SW5 |
| 1 | A | SW_PUSH_6mm | SW6 |
Show 22 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SW_DPST_x2 | PinHeader_1x05_P2.00mm_Vertical | SW7 |
| 1 | CTX33-3 | IND_CTX33-3-R | T1 |
| 3 | MBRS130LT3G | D_SMB_Handsoldering | D1, D2, D3 |
| 1 | TX | D_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D4 |
| 1 | RX | D_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D5 |
| 1 | 10u | L_Wuerth_MAPI-3012 | L1 |
| 2 | 22u | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1, C5 |
| 15 | 100n | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C2, C4, C7, C10, C11, C13, C14, C16 +7 |
| 1 | 2.2u | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C3 |
| 1 | 220n | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C6 |
| 1 | 10n | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C8 |
| 2 | 1u | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C9, C26 |
| 1 | 4.7u | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C12 |
| 4 | 10p | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C15, C17, C18, C19 |
| 1 | 22u | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C24 |
| 1 | 330 | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1 |
| 6 | 1k | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R2, R7, R8, R10, R11, R12 |
| 1 | 0.2 | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R3 |
| 2 | 100k | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R4, R5 |
| 1 | 24 | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R6 |
| 1 | 100 | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R9 |
| 12 | 10k | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R13, R14, R15, R16, R17, R18, R19, R20 +4 |
PSUtap digital design files
The KiCad project lives in the WEEE-Open/psutap repository on GitHub; these links point at the commit this page was built from.
PSUtap digital: common questions
What microcontroller does the PSUtap digital use?
The PSUtap digital is built around the ATmega328P-AU, from the AVR/Arduino family.
How big is the PSUtap digital PCB?
The PSUtap digital measures 92 × 70.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the PSUtap digital?
80 components, from 42 distinct parts. The full bill of materials is listed on this page.
Where can I download the PSUtap digital design files?
From the WEEE-Open/psutap repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the PSUtap digital design in my own project?
Yes, under the terms of its CERN-OHL-W-2.0 license, which WEEE-Open chose for the repository.
Can I test firmware for the PSUtap digital without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in psutap
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k