UTDRoboSubCompute

WilliamDATaylor·UTDRoboSubCompute

UTDRoboSubCompute PCB layout, top view — open source Raspberry Pi board by WilliamDATaylor

About the UTDRoboSubCompute PCB

UTDRoboSubCompute is an open source Raspberry Pi PCB design by WilliamDATaylor, published on GitHub under the MIT license. It is a 4-layer board measuring 100 × 100.1 mm, with 51 components from 28 distinct parts.

Its main chip is the ComputeModule5-CM5, from the Raspberry Pi family. Other key parts include the TPD4E05U06QDQARQ1, RT9742GGJ5, AP22653W6-7 and PCA9685PW,118. By type, the board carries 17 connectors, 14 resistors, 12 capacitors, 5 ICs and 2 LEDs.

It belongs with the dev boards & breakouts and robotics & motion designs in this gallery.

From the project

cm5 carrier board for the UTD RoboSub Team

This will compete in the 2026 MateROV competition.

Designs are heavily influenced by the reference RPI CM5 IO board.

1. Servo Controller 2. GPIO Pins 3. CSI/DSI 4. SD Card boot 5. Power Inputs 6. USB 2.0 7. USB 3.0 8. CM5 9. Fan 10. Sizing and dimensions 11. Trace Routing 12. Additional Details

Internally connected to GPIO 2 & GPIO 3 (I2c1). Info here

The Servo controller is on the x0 I2c address

UTDRoboSubCompute, from the project README
From the project README

Main components on the UTDRoboSubCompute

UTDRoboSubCompute bill of materials (BOM)

51 components, 28 distinct parts.

QtyPartRefs
2
TPD4E05U06QDQARQ1
IC1, IC2
1
RT9742GGJ5
U2
1
AP22653W6-7
U3
1
PCA9685PW,118
U4
1
Disable Bluetooth/Wifi
J1
1
GSB191217FHR
J2
1
ARJM11B1-502-NN-EW2
J3
1
GTFP08432B1HR
J4
1
Fan_Header
J5
3
Wago connector 2091-1372
J6, J7, J8
4
HEADER-3X04
J9, J10, J11, J12
1
Conn_02x20_Odd_Even
J13
2
GSB3116344KHHR
J14, J15
2
TF38-22S-0.5SV(830)
TF38-22S-0.5SV_830_
J16, J17
1
ComputeModule5-CM5
Module1
1
150120GS75000
Act1
1
150120RS75000
Pwr1
1
0.1u
C1
5
10u
C2, C3, C5, C6, C7
1
100u
C4
Show 8 more
QtyPartRefs
3
~
C8, C9, C10
2
0.1u
C11, C12
3
2.2K
R1, R2, R11
1
150
R3
4
10k
R4, R5, R6, R8
1
90
R9
1
12K
R10
4
220
RN1, RN2, RN3, RN4

UTDRoboSubCompute design files

The KiCad project lives in the WilliamDATaylor/UTDRoboSubCompute repository on GitHub; these links point at the commit this page was built from.

UTDRoboSubCompute: common questions

What microcontroller does the UTDRoboSubCompute use?

The UTDRoboSubCompute is built around the ComputeModule5-CM5, from the Raspberry Pi family.

How big is the UTDRoboSubCompute PCB?

The UTDRoboSubCompute measures 100 × 100.1 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the UTDRoboSubCompute?

51 components, from 28 distinct parts. The full bill of materials is listed on this page.

Where can I download the UTDRoboSubCompute design files?

From the WilliamDATaylor/UTDRoboSubCompute repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the UTDRoboSubCompute design in my own project?

Yes, under the terms of its MIT license, which WilliamDATaylor chose for the repository.

Can I test firmware for the UTDRoboSubCompute without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.

Similar boards