19 open source boards using the AP22653W6-7
Real designs built with the AP22653W6-7, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
PDNode Baseboard
DvidMakesThings
203 × 151.8 mm208 parts6LAGPL-3.086ESP32
Endeavour2
petrmikheev
100 × 85 mm263 parts6LGPL-3.049Dongle pro
fcjr
26 × 98 mm99 parts4LApache-2.016Raspberry Pi
Unifying
balthazar-space
120.9 × 78.8 mm121 parts4LCERN-OHL-S-2.07Raspberry Pi
Thesis
Dylancyclone
158.3 × 110 mm78 parts2LNo license1Raspberry Pi
Iasis
hydazz
130 × 100 mm636 parts6LApache-2.00Raspberry Pi
Hexa-Pi
rickcox
150 × 150 mm352 parts4LCC-BY-4.00STM32
Dual Axis Controller
jrseti
140 × 100 mm307 parts4LCC0-1.00STM32
RCM DishControllerBoard
jrseti
140 × 100 mm304 parts4LMIT0Minerva-Carrier
PyroFlareX
83.5 × 90 mm173 parts6LNo license0Giris
dubnubdubnub
70.1 × 60 mm136 parts4LApache-2.00Raspberry Pi
UTDRoboSubCompute
WilliamDATaylor
100 × 100.1 mm51 parts4LMIT0Raspberry Pi
Roboclaw cm4-dc dish controller
jrseti
145.8 × 76.9 mm49 parts2LMIT0- schematic only · 562 partsRaspberry Pi
OpenXTCM5-Head-Unit
mibs510
562 parts2LMIT0 ESP32
Endeavour2 upd
petrmikheev
100 × 85 mm238 parts6LGPL-3.049Dongle lite
fcjr
16 × 55 mm56 parts6LApache-2.016Compact cm5-desktop front io
CopperPilot
150 × 65 mm77 parts2LCERN-OHL-S-2.00Raspberry Pi
Cm4-robo controller
jrseti
145.8 × 76.9 mm49 parts2LCC0-1.00Dongle lite-1s4l
fcjr
22 × 77 mm56 parts4LApache-2.016
How designs wire the AP22653W6-7
Read from the KiCad layouts of 14 open source designs, one per repository: what each pin of the AP22653W6-7 connects to, and the resistors, capacitors and other passives placed on it.
- The ILIM_5 pin has a resistor to GND on 14 of 14 designs, most often 15 kΩ (then 33.2 kΩ).
- The IN_1 pin is tied to 5V on 14 of 14 designs.
- The OUT_6 pin is tied to VBUS on 9 of 14 designs (a signal on 5).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| IN_1pin 1 | Connected to: 5V 100% | — |
| GND_2pin 2 | Connected to: GND 100% | — |
| FAULT_4pin 4 | Connected to: USB2514B-I/M2 21% · not connected 21% |
|
| ILIM_5pin 5 | Connected to: Signal 100% |
|
| OUT_6pin 6 | Connected to: VBUS 64% · a signal 36% | — |
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PDNode Baseboard by DvidMakesThings, Endeavour2 by petrmikheev, Dongle lite by fcjr and Unifying-PCB by balthazar-space.
The AP22653W6-7 in open source designs
The gallery holds 19 open source boards using the AP22653W6-7 from 15 GitHub repositories; a typical one measures about 125.5 × 87.5 mm and carries around 136 components.
74% use four copper layers or more, and 89% carry an open source license.
The most starred is PDNode Baseboard by DvidMakesThings.
Parts used alongside the AP22653W6-7
Microcontrollers on boards using the AP22653W6-7
What boards using the AP22653W6-7 are built for
AP22653W6-7: common questions
Where can I find a AP22653W6-7 reference design?
Each of the 19 boards on this page is a real design using the AP22653W6-7. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the AP22653W6-7 ILIM_5 pin?
The ILIM_5 pin has a resistor to GND on 14 of 14 designs, most often 15 kΩ (then 33.2 kΩ). Counted from the KiCad layouts of 14 open source designs using the AP22653W6-7.
How is the AP22653W6-7 IN_1 pin connected?
The IN_1 pin is tied to 5V on 14 of 14 designs. Counted from the KiCad layouts of 14 open source designs using the AP22653W6-7.
How is the AP22653W6-7 OUT_6 pin connected?
The OUT_6 pin is tied to VBUS on 9 of 14 designs (a signal on 5). Counted from the KiCad layouts of 14 open source designs using the AP22653W6-7.
What parts are used alongside the AP22653W6-7?
The FSUSB42MUX, 74LVC1G07SE-7, AP64501SP-13, TPD4EUSB30 and TPD4EUSB30DQAR appear in the most repositories here.
Which microcontrollers do boards using the AP22653W6-7 use?
Most are built on Raspberry Pi (8), ESP32 (2) and STM32 (2).
How big is a typical board using the AP22653W6-7?
The median is 125.5 × 87.5 mm, and 26% are two-layer designs.
What is the most popular open source board using the AP22653W6-7?
By GitHub stars, PDNode Baseboard by DvidMakesThings, with 86 stars.
Can I simulate one of these boards using the AP22653W6-7 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.