55 open source boards using the RT9742GGJ5

Real designs built with the RT9742GGJ5, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

55 boardsClear filters|Most starred

How designs wire the RT9742GGJ5

Read from the KiCad layouts of 47 open source designs, one per repository: what each pin of the RT9742GGJ5 connects to, and the resistors, capacitors and other passives placed on it.

  • The OUT pin has a capacitor to GND on 45 of 47 designs, most often 10 µF (then 2.2 µF).
  • The NFLG pin is left unconnected on 44 of 47 designs (a signal on 3).
  • The IN pin is tied to 3.3V on 39 of 47 designs (a signal on 8).
  • The EN pin has a pull-up to 3.3V on 32 of 47 designs, most often 12 kΩ (then 10 kΩ).
OUTpin 1Connected to: A connector 85%
  • Capacitor to GND on 96% · 10 µF (41), 2.2 µF (2), 100 nF (2)
GNDpin 2Connected to: GND 98%
NFLGpin 3Connected to: Not connected 94%
ENpin 4Connected to: Signal 100%
  • Pull-up to 3.3V on 68% · 12 kΩ (21), 10 kΩ (10), 100 kΩ (1)
INpin 5Connected to: 3.3V 83% · a signal 17%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Wall Panel by dotstartech, Mesh radio-Halow-LoRa by ties1887, Astra piNas by jlcjak and CM5-SODIMM-Carrier by KaiPereira.

The RT9742GGJ5 in open source designs

The gallery holds 55 open source boards using the RT9742GGJ5 from 49 GitHub repositories; a typical one measures about 120.5 × 90 mm and carries around 71 components.

89% use four copper layers or more, and 45% carry an open source license.

The most starred is Wall Panel by dotstartech.

Microcontrollers on boards using the RT9742GGJ5

RT9742GGJ5: common questions

Where can I find a RT9742GGJ5 reference design?

Each of the 55 boards on this page is a real design using the RT9742GGJ5. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the RT9742GGJ5 OUT pin connected?

The OUT pin has a capacitor to GND on 45 of 47 designs, most often 10 µF (then 2.2 µF). Counted from the KiCad layouts of 47 open source designs using the RT9742GGJ5.

How is the RT9742GGJ5 NFLG pin connected?

The NFLG pin is left unconnected on 44 of 47 designs (a signal on 3). Counted from the KiCad layouts of 47 open source designs using the RT9742GGJ5.

How is the RT9742GGJ5 IN pin connected?

The IN pin is tied to 3.3V on 39 of 47 designs (a signal on 8). Counted from the KiCad layouts of 47 open source designs using the RT9742GGJ5.

What parts are used alongside the RT9742GGJ5?

The RT9742SNGV, AP22653W6, TPD4EUSB30, 74LVC1G07SE-7 and MagJack-A70-112-331N126 appear in the most repositories here.

Which microcontrollers do boards using the RT9742GGJ5 use?

Most are built on Raspberry Pi (37), RP2040/RP2350 (3), AVR/Arduino (2) and STM32 (2).

How big is a typical board using the RT9742GGJ5?

The median is 120.5 × 90 mm, and 11% are two-layer designs.

What is the most popular open source board using the RT9742GGJ5?

By GitHub stars, Wall Panel by dotstartech, with 366 stars.

Can I simulate one of these boards using the RT9742GGJ5 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part