USB-Meter
XFactHD·USB-Meter·Hardware/v1/USB-Meter.kicad_pcb
About the USB-Meter PCB
USB-Meter is an open source Microchip SAM PCB design by XFactHD, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 80.1 × 72.9 mm, with 80 components from 38 distinct parts.
Its main chip is the SAMD51J, from the Microchip SAM family. Other key parts include the USB2514B_Bi, AP2127K-3.3, USBLC6-2SC6, TPS2557 and MB85RS64. By type, the board carries 30 capacitors, 21 resistors, 9 ICs, 8 connectors, 5 switches and 3 diodes.
From the project
USB Power Meter
Main components on the USB-Meter
USB-Meter bill of materials (BOM)
80 components, 38 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | USB2514B_Bi | QFN-36-1EP_6x6mm_Pitch0.5mm | U1 |
| 1 | AP2127K-3.3 | SOT-23-5 | U2 |
| 2 | USBLC6-2SC6 | SOT-23-6 | U3, U4 |
| 1 | TPS2557 | DFN-8-1EP_3x3mm_Pitch0.65mm | U5 |
| 1 | MB85RS64 | SOIC-8_3.9x4.9mm_Pitch1.27mm | U6 |
| 1 | INA219 | SOT-23-8 | U8 |
| 1 | SAMD51J | TQFP-64_10x10mm_Pitch0.5mm | U9 |
| 1 | 74HC14 | SOIC-14_3.9x8.7mm_Pitch1.27mm | U11 |
| 1 | 24MHz | Crystal_SMD_2016-4pin_2.0x1.6mm | Y1 |
| 1 | 32.768kHz | Crystal_SMD_3215-2pin_3.2x1.5mm | Y2 |
| 1 | Screw_Terminal_01x02 | PhoenixContact_PTSM0,5_2-2,5-V | J1 |
| 1 | USB_B_Micro | USB_Micro-B_Molex_47346-0001 | J2 |
| 1 | USB_A | USB_A | J3 |
| 1 | Conn_02x04_Odd_Even | Pin_Header_Straight_2x04_Pitch1.27mm | J6 |
| 1 | Conn_02x04_Odd_Even | Pin_Header_Straight_2x04_Pitch1.27mm_SMD | J9 |
| 2 | Conn_01x02 | Pin_Header_Straight_1x02_Pitch1.27mm | J12, J13 |
| 1 | Conn_ARM_JTAG_SWD_10 | Pin_Header_Straight_2x05_Pitch1.27mm | J14 |
| 5 | SW_Push | SW_PUSH_6mm | SW2, SW3, SW4, SW5, SW6 |
| 1 | O128O064DLPP3N0000 | OLED_O128O064D-LPP3N00000 | DS1 |
| 1 | WS2812B | LED_WS2812B-PLCC4 | D1 |
Show 18 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 1N4001 | D_SOD-123 | D2, D3 |
| 1 | L | L_0805 | L1 |
| 3 | 2.2u | C_0805 | C1, C2, C3 |
| 7 | 10u | C_0805 | C4, C6, C23, C24, C25, C26, C27 |
| 2 | 1u | C_0805 | C5, C7 |
| 2 | 6p | C_0805 | C8, C9 |
| 2 | 8p | C_0805 | C10, C11 |
| 13 | 0.1u | C_0805 | C12, C13, C14, C15, C16, C17, C18, C19 +5 |
| 1 | 220u | CP_Tantalum_Case-D_EIA-7343-31_Reflow | C28 |
| 4 | 100k | R_0805 | R1, R2, R8, R9 |
| 1 | 12k | R_0805 | R3 |
| 1 | 50k | R_0805 | R4 |
| 1 | 33.2k | R_0805 | R5 |
| 2 | 4.7k | R_0805 | R6, R7 |
| 1 | 1 | R_2512 | R10 |
| 1 | 330k | R_0805 | R11 |
| 9 | 10k | R_0805 | R12, R13, R17, R18, R19, R20, R21, R22 +1 |
| 1 | 15k | R_0805 | R14 |
USB-Meter design files
The KiCad project lives in the XFactHD/USB-Meter repository on GitHub; these links point at the commit this page was built from.
USB-Meter: common questions
What microcontroller does the USB-Meter use?
The USB-Meter is built around the SAMD51J, from the Microchip SAM family.
How big is the USB-Meter PCB?
The USB-Meter measures 80.1 × 72.9 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the USB-Meter?
80 components, from 38 distinct parts. The full bill of materials is listed on this page.
Where can I download the USB-Meter design files?
From the XFactHD/USB-Meter repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the USB-Meter design in my own project?
Yes, under the terms of its GPL-3.0 license, which XFactHD chose for the repository.
Can I test firmware for the USB-Meter without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Microchip SAM firmware against it before you order a PCB.
Similar boards
Microchip SAM
Microcontroller Expansion Card
FrameworkComputer
26 × 30 mm24 parts2LCC-BY-4.01.1kMicrochip SAM
Taco Raven
VoronDesign
120 × 113 mm349 parts4LGPL-3.01.1kMicrochip SAM
Fpgaboy
Wren6991
50 × 50 mm89 parts4LNo license511Microchip SAM
OpenDropV4
GaudiLabs
124 × 115.4 mm118 parts2LGPL-3.0487Microchip SAM
ModulAdapter universal
GaudiLabs
100 × 69.5 mm45 parts2LGPL-3.0487Microchip SAM
Kira
kiibohd
366.9 × 114.3 mm400 partsCERN-OHL-1.2416