23 open source boards using the INA219
Real designs built with the INA219, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
SmartSupply
ThomasVDD
169.3 × 128 mm131 parts2LCustom license96NXP
Kbox hardware
sarfata
100 × 54 mm102 parts2LNo license19AVR/Arduino
PSU
ThomasVDD
50 × 100 mm116 parts2LCustom license16ESP32
WLED-Controller
LostInCompilation
100 × 100 mm63 parts2LNo license7AVR/Arduino
Interface board
uvmaero
157.5 × 109.2 mm70 parts2LCC-BY-SA-4.03AVR/Arduino
PowerBox
frep
90 × 55 mm103 parts2LNo license2EPS v1
Migsster
85 × 85 mm25 parts2LNo license2Greenhouse Control Unit
nbolton
188 × 90.2 mm85 parts4LNo license1PIC
Mia
OpenKeyboards
376.2 × 171.5 mm341 parts2LNo license0STM32
LithiumBMS
JiriS97
64.8 × 39.4 mm125 parts2LMIT0RP2040/RP2350
Wigglecam controller
jadenrhee
76 × 50 mm98 parts4LNo license0Microchip SAM
USB-Meter
XFactHD
80.1 × 72.9 mm80 parts4LGPL-3.00ESP32
TankSync tx
gargsrishtii
100 × 100 mm38 parts2LCERN-OHL-P-2.00Beaglebone usbasp cape
thinnect
86.4 × 54.6 mm18 parts2LCustom license0Voltage---current sensor-INA219-breakout hardware design
SolderedElectronics
38 × 22 mm16 parts2LTAPR-OHL-1.00- schematic only · 25 partsESP32
MyoCell
KenKadilar
25 partsMIT0 AVR/Arduino
DC DCBoard
uvmaero
185.4 × 68.6 mm65 parts2LCC-BY-SA-4.03Lps regulator rev 12
jerryok826
136.2 × 62.6 mm122 parts2LMIT1Power Meter
sicrisembay
29 × 29 mm17 parts2LMIT0AVR/Arduino
GLVColoumbCounterTest
uvmaero
80.9 × 36.2 mm43 parts2LCC-BY-SA-4.03ESP8266
EspDevBoard
frep
69.9 × 66 mm50 parts2LNo license2ESP32
Fuente Simetrica
EmersonEE
120.3 × 100 mm74 parts2LNo license0STM32
Forge-Probe: Silicon Backdoor Debug Probe
jayis1
37 × 23 mm11 parts4LNo license3
How designs wire the INA219
Read from the KiCad layouts of 19 open source designs, one per repository: what each pin of the INA219 connects to, and the resistors, capacitors and other passives placed on it.
- The SCL pins have a pull-up to 3.3V on 12 of 19 designs, most often 4.7 kΩ (then 3.3 kΩ).
- The SDA pins have a pull-up to 3.3V on 12 of 18 designs, most often 4.7 kΩ (then 3.3 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SCLpin 3, 5 | Connected to: A connector 24%, the microcontroller 24% · GND 24% |
|
| SDApin 4, 6 | Connected to: The microcontroller 28%, a connector 22% · 3.3V 28% |
|
| A0pin 7 | Connected to: Signal 53% · GND 40% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include SmartSupply by ThomasVDD, Kbox hardware by sarfata, PSU PCB by ThomasVDD and WLED-Controller-PCB by LostInCompilation.
The INA219 in open source designs
The gallery holds 23 open source boards using the INA219 from 20 GitHub repositories; a typical one measures about 88.2 × 67.3 mm and carries around 70 components.
82% are two-layer designs, the rest use four layers or more, and 43% carry an open source license.
The most starred is SmartSupply by ThomasVDD.
Parts used alongside the INA219
Microcontrollers on boards using the INA219
What boards using the INA219 are built for
INA219: common questions
Where can I find a INA219 reference design?
Each of the 23 boards on this page is a real design using the INA219. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the INA219 SCL pin?
The SCL pins have a pull-up to 3.3V on 12 of 19 designs, most often 4.7 kΩ (then 3.3 kΩ). Counted from the KiCad layouts of 19 open source designs using the INA219.
What pull-up resistor is used on the INA219 SDA pin?
The SDA pins have a pull-up to 3.3V on 12 of 18 designs, most often 4.7 kΩ (then 3.3 kΩ). Counted from the KiCad layouts of 19 open source designs using the INA219.
What parts are used alongside the INA219?
The 74HC595, AMS1117-3.3, LM334, LM358 and LM7805CT appear in the most repositories here.
Which microcontrollers do boards using the INA219 use?
Most are built on AVR/Arduino (6), ESP32 (4), STM32 (2) and NXP (1).
How big is a typical board using the INA219?
The median is 88.2 × 67.3 mm, and 82% are two-layer designs.
What is the most popular open source board using the INA219?
By GitHub stars, SmartSupply by ThomasVDD, with 96 stars.
Can I simulate one of these boards using the INA219 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.