Zdenduino normal

zdenekru·ZdenduinoRXX

Zdenduino normal PCB layout, top view — open source ESP32 board by zdenekru

About the Zdenduino normal PCB

Zdenduino normal is an open source ESP32 PCB design by zdenekru, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 31 × 42 mm, with 29 components from 15 distinct parts.

Its main chip is the ESP32-C3-WROOM-02, from the ESP32 family. Other key parts include the USBLC6-2SC6 and AP2112K-3.3. By type, the board carries 10 capacitors, 9 resistors, 3 ICs, 3 connectors, 2 switches and 1 crystal.

It belongs with the iot & wireless, dev boards & breakouts and usb & debug tools designs in this gallery.

From the project

My own flavor of MCU dev board based on ESP32-C3-WROOM-02

A compact custom ESP32-C3 development board designed in KiCad and manufactured through JLCPCB.

Zdenduino started as a learning project focused on:

- Custom PCB design - ESP32-C3 bring-up - USB routing and impedance considerations - Practical embedded hardware development - PCBA manufacturing with JLCPCB

The result is a compact 31x42 mm 2-layer PCB based on the ESP32-C3-WROOM module.

Main components on the Zdenduino normal

Zdenduino normal bill of materials (BOM)

29 components, 15 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
USBLC6-2SC6
U1
1
AP2112K-3.3
U2
1
ESP32-C3-WROOM-02
U3
1
Crystal
Y1
1
USB_C_RECEPTACLE_USB2.0_16P
USB_C_Receptacle_USB2.0_16P
J1
2
CONN_01X08_PIN
Conn_01x08_Pin
J2, J3
2
SW_Push
SW1, SW2
1
LESD8D5.0T5G
D1
5
4U7
4u7
C1, C2, C3, C4, C5
3
100N
100n
C6, C9, C10
2
12P
12p
C7, C8
2
5K1
5k1
R1, R2
2
0R
R3, R4
4
10K
10k
R5, R7, R8, R9
1
100R
R6

Zdenduino normal design files

The KiCad project lives in the zdenekru/ZdenduinoRXX repository on GitHub; these links point at the commit this page was built from.

Zdenduino normal: common questions

What microcontroller does the Zdenduino normal use?

The Zdenduino normal is built around the ESP32-C3-WROOM-02, from the ESP32 family.

How big is the Zdenduino normal PCB?

The Zdenduino normal measures 31 × 42 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Zdenduino normal?

29 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Zdenduino normal design files?

From the zdenekru/ZdenduinoRXX repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Zdenduino normal design in my own project?

Yes, under the terms of its GPL-3.0 license, which zdenekru chose for the repository.

Can I test firmware for the Zdenduino normal without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in ZdenduinoRXX

Similar boards