Zdenduino vcut
zdenekru·ZdenduinoRXX
About the Zdenduino vcut PCB
Zdenduino vcut is an open source ESP32 PCB design by zdenekru, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 64.9 × 65.6 mm, with 29 components from 15 distinct parts.
Its main chip is the ESP32-C3-WROOM-02, from the ESP32 family. Other key parts include the USBLC6-2SC6 and AP2112K-3.3. By type, the board carries 10 capacitors, 9 resistors, 3 ICs, 3 connectors, 2 switches and 1 crystal.
It belongs with the iot & wireless, dev boards & breakouts and usb & debug tools designs in this gallery.
From the project
My own flavor of MCU dev board based on ESP32-C3-WROOM-02
A compact custom ESP32-C3 development board designed in KiCad and manufactured through JLCPCB.
Zdenduino started as a learning project focused on:
- Custom PCB design - ESP32-C3 bring-up - USB routing and impedance considerations - Practical embedded hardware development - PCBA manufacturing with JLCPCB
The result is a compact 31x42 mm 2-layer PCB based on the ESP32-C3-WROOM module.
Main components on the Zdenduino vcut
Zdenduino vcut bill of materials (BOM)
29 components, 15 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | USBLC6-2SC6 | SOT-23-6_Handsoldering | U1 |
| 1 | AP2112K-3.3 | SOT-23-5_HandSoldering | U2 |
| 1 | ESP32-C3-WROOM-02 | ESP32-C3-WROOM-02 | U3 |
| 1 | Crystal | Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | USB_C_RECEPTACLE_USB2.0_16P USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J1 |
| 2 | CONN_01X08_PIN Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J2, J3 |
| 2 | SW_Push | SW_SPST_B3U-1000P | SW1, SW2 |
| 1 | LESD8D5.0T5G PESD5V0L1ULD | D_SOD-882D | D1 |
| 5 | 4U7 4u7 | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C3, C4, C5 |
| 3 | 100N 100n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C6, C9, C10 |
| 2 | 12P 12p | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C7, C8 |
| 2 | 5K1 5k1 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
| 2 | 0R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R4 |
| 4 | 10K 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R7, R8, R9 |
| 1 | 100R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6 |
Zdenduino vcut design files
The KiCad project lives in the zdenekru/ZdenduinoRXX repository on GitHub; these links point at the commit this page was built from.
Zdenduino vcut: common questions
What microcontroller does the Zdenduino vcut use?
The Zdenduino vcut is built around the ESP32-C3-WROOM-02, from the ESP32 family.
How big is the Zdenduino vcut PCB?
The Zdenduino vcut measures 64.9 × 65.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Zdenduino vcut?
29 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Zdenduino vcut design files?
From the zdenekru/ZdenduinoRXX repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Zdenduino vcut design in my own project?
Yes, under the terms of its GPL-3.0 license, which zdenekru chose for the repository.
Can I test firmware for the Zdenduino vcut without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in ZdenduinoRXX
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k