Car alarm
zeyad-hisham-cyper·Freelance-Projects·Smart-Emergency-Dispatch-Sensor/car_alarm.kicad_pcb
About the Car alarm PCB
Car alarm is an open source ESP32 PCB design by zeyad-hisham-cyper, published on GitHub. It is a 2-layer board measuring 100 × 60 mm, with 17 components from 14 distinct parts.
Its main chip is the ESP32-DEVKITC-32E, from the ESP32 family. Other key parts include the GY-521, MLX90614ESF-BAA-000-TU and LM7805_TO220. By type, the board carries 5 capacitors, 4 ICs, 2 connectors, 2 diodes, 2 resistors and 1 buzzer.
It belongs with the iot & wireless, sensors and rf & radio designs in this gallery.
From the project
An ESP32-based sensor board that pairs an IR thermometer with a 6-axis motion sensor and a GPS header, built to detect heat, fire or impact events and raise a local alarm. Designed in KiCad 9 as a 2-layer, 100 × 60 mm through-hole PCB.
An ESP32-based sensor board that pairs an IR thermometer with a 6-axis motion sensor and a GPS header, built to detect heat, fire or impact events and raise a local alarm. Designed in KiCad 9 as a 2-layer, 100 × 60 mm through-hole PCB.
The Smart Emergency Dispatch Sensor is a carrier PCB for an ESP32-DevKitC-32E module. It brings together:
- an MLX90614 non-contact infrared temperature sensor, for heat and fire detection, - a GY-521 (MPU-6050) accelerometer/gyroscope breakout, for motion, tilt or impact detection (inferred from the "MPU Sensor" block), - a 4-pin UART header marked "GPS…

Main components on the Car alarm
Car alarm bill of materials (BOM)
17 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | GY-521 | GY-521 | U1 |
| 1 | MLX90614ESF-BAA-000-TU | TO254P942H425-4 | U2 |
| 1 | ESP32-DEVKITC-32E | MODULE_ESP32-DEVKITC-32E | U3 |
| 1 | LM7805_TO220 | TO-220-3_Vertical | U6 |
| 1 | Conn_01x04_Pin | PinSocket_1x04_P2.54mm_Horizontal | J1 |
| 1 | Barrel_Jack_Switch | BarrelJack_Horizontal | J9 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | SW_Wuerth_450301014042 | SW_Slide-03_Wuerth-WS-SLTV_10x2.5x6.4_P2.54mm | SW1 |
| 1 | Heat | LED_D5.0mm | D5 |
| 1 | Fire | LED_D5.0mm | D6 |
| 3 | 0.1uF | C_Radial_D5.0mm_H5.0mm_P2.00mm | C1, C4, C5 |
| 1 | 100uF | C_Radial_D5.0mm_H5.0mm_P2.00mm | C2 |
| 1 | 0.33uF | C_Radial_D5.0mm_H5.0mm_P2.00mm | C3 |
| 2 | 220 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R6, R7 |
Car alarm design files
The KiCad project lives in the zeyad-hisham-cyper/Freelance-Projects repository on GitHub; these links point at the commit this page was built from.
Car alarm: common questions
What microcontroller does the Car alarm use?
The Car alarm is built around the ESP32-DEVKITC-32E, from the ESP32 family.
How big is the Car alarm PCB?
The Car alarm measures 100 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Car alarm?
17 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the Car alarm design files?
From the zeyad-hisham-cyper/Freelance-Projects repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Car alarm design in my own project?
The repository has no license, so all rights stay with zeyad-hisham-cyper. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Car alarm without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Freelance-Projects
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k