Cow
zeyad-hisham-cyper·Freelance-Projects·Cow-Health-Monitor/cow_pcb/cow_pcb.kicad_pcb
About the Cow PCB
Cow is an open source ESP32 PCB design by zeyad-hisham-cyper, published on GitHub. It is a 2-layer board measuring 81.4 × 59.8 mm, with 19 components from 13 distinct parts.
Its main chip is the ESP32-DEVKITC-32E, from the ESP32 family. Other key parts include the GY-906, GY-87 and LM7805. By type, the board carries 8 connectors, 4 ICs, 4 capacitors, 2 resistors and 1 switch.
It belongs with the iot & wireless, sensors and rf & radio designs in this gallery.
From the project
An ESP32 carrier board and two small sensor boards for a wearable that monitors a cow's vital signs. It brings together body temperature, heart rate / SpO₂, motion and GPS on one powered PCB set, designed in KiCad 9.
An ESP32 carrier board and two small sensor boards for a wearable that monitors a cow's vital signs. It brings together body temperature, heart rate / SpO₂, motion and GPS on one powered PCB set, designed in KiCad 9.
This is the hardware for a livestock health monitor. A carrier board holds an ESP32-DevKitC-32E and connects it to:
- a non-contact IR thermometer (GY-906 module, MLX90614-class) for body/skin temperature - pulse-oximeter / heart-rate modules (DFRobot SEN0344, MAX30102-based) - a 10-DOF motion module (GY-87: accelerometer/gyro/magnetometer/barometer) for activity and posture -…

Main components on the Cow
Cow bill of materials (BOM)
19 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | GY-906 | Untitled | U1 |
| 1 | GY-87 | GY-87 | U2 |
| 1 | ESP32-DEVKITC-32E | MODULE_ESP32-DEVKITC-32E | U3 |
| 1 | LM7805 | TO-220-3_Vertical | U6 |
| 1 | GPS MODULE | PinSocket_1x04_P2.54mm_Horizontal | J1 |
| 2 | Conn_01x02_Pin | PinHeader_1x02_P2.54mm_Vertical | J3, J4 |
| 4 | JST_1mm_4 | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J5, J6, J7, J8 |
| 1 | Barrel_Jack_Switch | BarrelJack_Horizontal | J9 |
| 1 | SW_Wuerth_450301014042 | SW_Slide-03_Wuerth-WS-SLTV_10x2.5x6.4_P2.54mm | SW1 |
| 2 | 0.1uF | C_Radial_D5.0mm_H5.0mm_P2.00mm | C1, C4 |
| 1 | 100uF | C_Radial_D5.0mm_H5.0mm_P2.00mm | C2 |
| 1 | 0.33uF | C_Radial_D5.0mm_H5.0mm_P2.00mm | C3 |
| 2 | 2k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2 |
Cow design files
The KiCad project lives in the zeyad-hisham-cyper/Freelance-Projects repository on GitHub; these links point at the commit this page was built from.
Cow: common questions
What microcontroller does the Cow use?
The Cow is built around the ESP32-DEVKITC-32E, from the ESP32 family.
How big is the Cow PCB?
The Cow measures 81.4 × 59.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Cow?
19 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the Cow design files?
From the zeyad-hisham-cyper/Freelance-Projects repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Cow design in my own project?
The repository has no license, so all rights stay with zeyad-hisham-cyper. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Cow without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Freelance-Projects
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k