Can atmega
Zwackelmann·brewbot·pcb/can-atmega/can-atmega.kicad_pcb
About the Can atmega PCB
Can atmega is an open source AVR/Arduino PCB design by Zwackelmann, published on GitHub. It is a 2-layer board measuring 37 × 48 mm, with 26 components from 16 distinct parts.
Its main chip is the ATmega328P-A, from the AVR/Arduino family. Other key parts include the LM1117-5.0, TJA1051T and MCP2515-xSO. By type, the board carries 12 capacitors, 4 ICs, 3 connectors, 3 resistors, 2 crystals and 1 LED.
Main components on the Can atmega
Can atmega bill of materials (BOM)
26 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM1117-5.0 | SOT-223 | U1 |
| 1 | TJA1051T | SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | MCP2515-xSO | SOIC-18W_7.5x11.6mm_P1.27mm | U3 |
| 1 | ATmega328P-A | TQFP-32_7x7mm_P0.8mm | U4 |
| 2 | 16MHz | Crystal_HC49-4H_Vertical | X1, X2 |
| 1 | Screw_Terminal_01x05 | 4301207 | J1 |
| 1 | Conn_02x03_Odd_Even | IDC-Header_2x03_P2.54mm_Vertical | J3 |
| 1 | Connector_female_4x8 | Connector_female_4x8 | J4 |
| 1 | Green | LED_0805_2012Metric | LED1 |
| 1 | 10uH | L_Neosid_SMS-ME3010 | L1 |
| 1 | 1uF | C_1206_3216Metric | C1 |
| 2 | 10uF/16V | CP_EIA-3216-18_Kemet-A | C2, C7 |
| 5 | 0.1uF | C_1206_3216Metric | C3, C4, C8, C9, C10 |
| 4 | 22PF | C_1206_3216Metric | C5, C6, C11, C12 |
| 1 | 1K | R_0805_2012Metric | R1 |
| 2 | 10K | R_0805_2012Metric | R2, R3 |
Can atmega design files
The KiCad project lives in the Zwackelmann/brewbot repository on GitHub; these links point at the commit this page was built from.
Can atmega: common questions
What microcontroller does the Can atmega use?
The Can atmega is built around the ATmega328P-A, from the AVR/Arduino family.
How big is the Can atmega PCB?
The Can atmega measures 37 × 48 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Can atmega?
26 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the Can atmega design files?
From the Zwackelmann/brewbot repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Can atmega design in my own project?
The repository has no license, so all rights stay with Zwackelmann. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Can atmega without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in brewbot
AVR/Arduino
Can atmega layout-2025-07-01
Zwackelmann
111 × 150 mm39 parts2LNo license0AVR/Arduino
Temp sensor
Zwackelmann
52.5 × 52.5 mm36 parts2LNo license0Can atmega-02-layout2
Zwackelmann
114 × 56 mm16 parts2LNo license0AVR/Arduino
Temp module
Zwackelmann
37 × 27 mm15 parts2LNo license0Motor module
Zwackelmann
37 × 27 mm7 parts2LNo license0
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k