Esp

0Zane·E.L.B.E.R.R·hardware/esp/esp.kicad_pcb

Esp PCB layout, top view — open source ESP32 board by 0Zane

About the Esp PCB

Esp is an open source ESP32 PCB design by 0Zane, published on GitHub under the MIT license. It is a 2-layer board measuring 100 × 80 mm, with 82 components from 40 distinct parts.

Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the AMS1117-3.3, CP2102N-AXX-XQFN20, VL53L0X, NRF24L01 and BME280. By type, the board carries 25 capacitors, 24 resistors, 12 diodes, 9 connectors, 6 ICs and 3 inductors.

It belongs with the robotics & motion designs in this gallery.

From the project

Fanmade of E.LB.E.R.R. robot by LightsAreOff

Main components on the Esp

Esp bill of materials (BOM)

82 components, 40 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
AMS1117-3.3
U1
1
CP2102N-AXX-XQFN20
CP2102N-Axx-xQFN20
U2
1
ESP32-S3-WROOM-1
U3
1
VL53L0X
U4
1
NRF24L01
U5
1
BME280
U6
1
16MHZ
16MHz
Y1
3
CONN_01X02
Conn_01x02
J1, J4, J9
2
USB_C_RECEPTACLE_USB2.0_16P
USB_C_Receptacle_USB2.0_16P
J2, J3
1
Conn_Coaxial
J5
2
CONN_01X09_PIN
Conn_01x09_Pin
J6, J8
1
CONN_01X06_PIN
Conn_01x06_Pin
J7
1
RESET
SW1
1
BOOT
SW2
6
D_TVS
D1, D2, D3, D10, D11, D12
6
LED
D4, D5, D6, D7, D8, D9
1
8.2NH
8.2nH
L1
1
3.9NH
3.9nH
L2
1
2.7NH
2.7nH
L3
4
10UF
10uF
C1, C3, C7, C9
Show 20 more
QtyPartRefs
8
0.1UF
0.1uF
C2, C4, C6, C10, C15, C23, C24, C25
3
4.7UF
4.7uF
C5, C11, C18
1
0.1µF
C8
1
10NF
10nF
C12
1
1NF
1nF
C13
1
33NF
33nF
C14
2
22PF
22pF
C16, C19
1
2.2NF
2.2nF
C17
1
4.7PF
4.7pF
C20
1
1.5PF
1.5pF
C21
1
1PF
1pF
C22
4
5.1K
5.1k
R1, R2, R5, R6
2
22R
R3, R4
7
1k
R7, R8, R11, R12, R13, R14, R19
3
10K
R9, R10, R24
4
4.7K
4.7k
R15, R16, R20, R21
1
22K
R17
1
1M
R18
1
47.5K
47.5k
R22
1
22.1K
22.1k
R23

Esp design files

The KiCad project lives in the 0Zane/E.L.B.E.R.R repository on GitHub; these links point at the commit this page was built from.

Esp: common questions

What microcontroller does the Esp use?

The Esp is built around the ESP32-S3-WROOM-1, from the ESP32 family.

How big is the Esp PCB?

The Esp measures 100 × 80 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Esp?

82 components, from 40 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Esp design files?

From the 0Zane/E.L.B.E.R.R repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Esp design in my own project?

Yes, under the terms of its MIT license, which 0Zane chose for the repository.

Can I test firmware for the Esp without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in E.L.B.E.R.R

Similar boards