SDWire
agners·sd-mux·doc/hardware/SDWire/SDWire.kicad_pcb
About the SDWire PCB
SDWire is an open source PCB design by agners, published on GitHub under the Apache-2.0 license. It is a 4-layer board measuring 21.6 × 48.4 mm, with 65 components from 28 distinct parts.
Other key parts include the USB2640-HZH-02, SPX3819M5, FT200XD, MC74HC1G04DTT1G and TS3A27518EPWR. By type, the board carries 26 capacitors, 16 resistors, 8 diodes, 6 ICs, 3 connectors and 3 inductors.
It belongs with the usb & debug tools designs in this gallery.
From the project
Fork of sd-mux from https://git.tizen.org/cgit/tools/testlab/sd-mux/ with SDReWire support
Fork of sd-mux-ctrl from the Tizen git repository. This version supports SDReWire as well as SDWire. To use this version make sure to set the product string.
Use the "set-serial" command to write serial as well as product string:
With that you should be able to switch between DUT (device under test) and TS (test system) mode:
Note: Since sd-mux-ctrl needs full device access using sd-mux-ctrl does not allow you to use the USB to UART tty at the same time. This fork is meant as a stop-gap/migration solution.
Main components on the SDWire
SDWire bill of materials (BOM)
65 components, 28 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | USB2640-HZH-02 | QFN-48-1EP_7x7mm_Pitch0.5mm | U1 |
| 1 | SPX3819M5 | SOT-23-5 | U2 |
| 1 | FT200XD | DFN-10-1EP_3x3mm_Pitch0.5mm | U3 |
| 1 | MC74HC1G04DTT1G | SOT-23-5 | U4 |
| 1 | TS3A27518EPWR | TSSOP-24 | U5 |
| 1 | AT24CS02-SSHM | SO-8_3.9x4.9mm_P1.27mm | U6 |
| 2 | MMBT4403LT1 | SOT-23 | Q3, Q4 |
| 1 | 24MHz | Crystal_SMD_2520-4pin_2.5x2.0mm | Y1 |
| 1 | usd-plug | usd | J1 |
| 1 | uSD Socket | usd-attend | J2 |
| 1 | USB_OTG_MICRO_USB | micro_sub_molex | P1 |
| 1 | OSB50402C1E | LED_0402 | D1 |
| 2 | RED | LED_0402 | D2, D5 |
| 3 | BLUE | LED_0402 | D3, D6, D7 |
| 2 | GREEN | LED_0402 | D4, D8 |
| 3 | BLM15PD121SN1D | R_0402 | L1, L2, L3 |
| 15 | 100nF/16V | C_0402 | C1, C2, C6, C8, C9, C11, C12, C13 +7 |
| 2 | 33p/50V | C_0402 | C3, C4 |
| 4 | 1uF/16V | C_0402 | C5, C7, C19, C21 |
| 3 | 10uF/10V | CP_Tantalum_Case-A_EIA-3216-18_Reflow | C10, C14, C27 |
Show 8 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 47pF | C_0402 | C22, C23 |
| 4 | 10K | R_0402 | R1, R2, R9, R10 |
| 1 | 1M | R_0402 | R3 |
| 1 | 12k 1% | R_0402 | R4 |
| 1 | 330R | R_0402 | R5 |
| 2 | 27R | R_0402 | R6, R7 |
| 2 | 10K | R_0402_1005Metric | R8, R16 |
| 5 | 1K | R_0402 | R11, R12, R13, R14, R15 |
SDWire design files
The KiCad project lives in the agners/sd-mux repository on GitHub; these links point at the commit this page was built from.
SDWire: common questions
How big is the SDWire PCB?
The SDWire measures 21.6 × 48.4 mm, has 4 copper layers and is 0.8 mm thick.
How many components are on the SDWire?
65 components, from 28 distinct parts. The full bill of materials is listed on this page.
Where can I download the SDWire design files?
From the agners/sd-mux repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the SDWire design in my own project?
Yes, under the terms of its Apache-2.0 license, which agners chose for the repository.
More boards in sd-mux
Similar boards
USB Hub Test
osy
50 × 50 mm85 parts4LCC-BY-4.0703XG Station Power
osy
54.3 × 91 mm9 parts2LCC-BY-4.0703FW-EC-DongleHiderPlus
LeoDJ
28.2 × 26.1 mm14 parts4LCERN-OHL-W-2.0497Adapter tsop48
bbogush
48 × 33 mm3 parts2LGPL-3.0389Adapter tsop48 solder
bbogush
48 × 33 mm3 parts2LGPL-3.0389Adapter soic8 solder
bbogush
48 × 20 mm3 parts2LGPL-3.0389