ESP32-S3-Dev-Board-Project
andresmoreno2702-gif·ESP32-S3-Dev-Board-Project·Project Files/KICAD FILES/ESP32 Dev module.kicad_pcb
About the ESP32-S3-Dev-Board-Project
ESP32-S3-Dev-Board-Project is an open source ESP32 PCB design by andresmoreno2702-gif, published on GitHub under the MIT license. It is a 4-layer board measuring 26.4 × 56.9 mm, with 26 components from 16 distinct parts.
Its main chip is the ESP32-S3-MINI-1-N8, from the ESP32 family. Other key parts include the D3V3XA4B10LP, TLV75801PDRV and ENS210. By type, the board carries 8 resistors, 7 capacitors, 4 ICs, 3 connectors and 2 diodes.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
All KICAD Files and Schematics
Custom 4-layer ESP32-S3 development board designed in KiCad 9. Manufactured by JLCPCB using the JLC04161H-3313 stackup.
Main components on the ESP32-S3-Dev-Board-Project
ESP32-S3-Dev-Board-Project bill of materials (BOM)
26 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | D3V3XA4B10LP | Diodes_UDFN-10_1.0x2.5mm_P0.5mm | U1 |
| 1 | TLV75801PDRV | WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm | U2 |
| 1 | ENS210 | AMS_QFN-4-1EP_2x2mm_P0.95mm_EP0.7x1.6mm | U3 |
| 1 | ESP32-S3-MINI-1-N8 | ESP32-S3-MINI-1-N8 | U4 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 2 | Conn_01x22_Pin | PinHeader_1x22_P2.54mm_Vertical | J2, J3 |
| 2 | SW_MEC_5E | PTS810SJG250SMTRLFS | BOOT1, RESET1 |
| 1 | WS2812B | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1 |
| 1 | LED | LED_0603_1608Metric | D2 |
| 3 | 10uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C3, C7 |
| 4 | 0.1uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C4, C5, C6 |
| 2 | 5.1k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 1 | 1M | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
| 1 | 200k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4 |
| 1 | 680 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5 |
| 3 | 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6, R7, R8 |
ESP32-S3-Dev-Board-Project design files
The KiCad project lives in the andresmoreno2702-gif/ESP32-S3-Dev-Board-Project repository on GitHub; these links point at the commit this page was built from.
ESP32-S3-Dev-Board-Project: common questions
What microcontroller does the ESP32-S3-Dev-Board-Project use?
The ESP32-S3-Dev-Board-Project is built around the ESP32-S3-MINI-1-N8, from the ESP32 family.
How big is the ESP32-S3-Dev-Board-Project?
The ESP32-S3-Dev-Board-Project measures 26.4 × 56.9 mm, has 4 copper layers and is 0.19 mm thick.
How many components are on the ESP32-S3-Dev-Board-Project?
26 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the ESP32-S3-Dev-Board-Project design files?
From the andresmoreno2702-gif/ESP32-S3-Dev-Board-Project repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the ESP32-S3-Dev-Board-Project design in my own project?
Yes, under the terms of its MIT license, which andresmoreno2702-gif chose for the repository.
Can I test firmware for the ESP32-S3-Dev-Board-Project without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k