8 open source boards using the ENS210
Real designs built with the ENS210, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
AirCube
StuckAtPrototype
45 × 45 mm52 parts2LApache-2.0357ESP32
ESP-32-Dev-Board
Fred98246
25.4 × 62.7 mm27 parts4LMIT2ESP32
O-hareAir
Will946
53.1 × 57.7 mm43 parts2LMIT1ESP32
Carbon
Enderman8843
46.3 × 43.4 mm31 parts2LNo license0ESP32
WeatherStation
kermitsgonnakermicide
38.4 × 33.5 mm27 parts4LNo license0ESP32
ESP32-S3-Dev-Board-Project
andresmoreno2702-gif
26.4 × 56.9 mm26 parts4LMIT0Mess-Sense+USBC
unicab369
99.1 × 99.1 mm440 parts2LNo license0Environmental-Sensors
basilfx
20.3 × 18 mm12 parts2LCC-BY-NC-4.024
How designs wire the ENS210
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the ENS210 connects to, and the resistors, capacitors and other passives placed on it.
- The SCL pin has a pull-up to 3.3V on 8 of 8 designs, most often 10 kΩ (then 4.7 kΩ).
- The SDA pin has a pull-up to 3.3V on 8 of 8 designs, most often 10 kΩ (then 4.7 kΩ).
- The VDD pin has a decoupling capacitor on 6 of 8 designs, most often 100 nF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDpin 1 | Connected to: 3.3V 100% |
|
| SCLpin 2 | Connected to: The microcontroller 75%, a connector 50%, ENS161 25% |
|
| SDApin 3 | Connected to: The microcontroller 75%, a connector 50%, ENS161 25% |
|
| GNDpin 4, 5 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include AirCube by StuckAtPrototype, Environmental-Sensors by basilfx, ESP-32-Dev-Board by Fred98246 and O-hareAir by Will946.
The ENS210 in open source designs
The gallery holds 8 open source boards using the ENS210 from 8 GitHub repositories; a typical one measures about 41.7 × 50.9 mm and carries around 29 components.
63% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is AirCube by StuckAtPrototype.
Parts used alongside the ENS210
Microcontrollers on boards using the ENS210
What boards using the ENS210 are built for
ENS210: common questions
Where can I find a ENS210 reference design?
Each of the 8 boards on this page is a real design using the ENS210. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the ENS210 SCL pin?
The SCL pin has a pull-up to 3.3V on 8 of 8 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 8 open source designs using the ENS210.
What pull-up resistor is used on the ENS210 SDA pin?
The SDA pin has a pull-up to 3.3V on 8 of 8 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 8 open source designs using the ENS210.
What decoupling capacitors do designs use on the ENS210 VDD pin?
The VDD pin has a decoupling capacitor on 6 of 8 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 8 open source designs using the ENS210.
What parts are used alongside the ENS210?
The TLV75801PDRV, AP2205, D3V3XA4B10LP, ENS161 and ESP32-H2-MINI-1 appear in the most repositories here.
Which microcontrollers do boards using the ENS210 use?
Most are built on ESP32 (6).
How big is a typical board using the ENS210?
The median is 41.7 × 50.9 mm, and 63% are two-layer designs.
What is the most popular open source board using the ENS210?
By GitHub stars, AirCube by StuckAtPrototype, with 357 stars.
Can I simulate one of these boards using the ENS210 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.