Dongle Alive v2.0
AntonioSilva584·Dongle_Alive_v2.0
About the Dongle Alive v2.0 PCB
Dongle Alive v2.0 is an open source ESP32 PCB design by AntonioSilva584, published on GitHub. It is a 4-layer board measuring 45 × 55 mm, with 53 components from 26 distinct parts.
Its main chip is the ESP32-WROOM-32, from the ESP32 family. Other key parts include the AMS1117, TJA1050, MCP2515-I_SO and CP2102N-Axx-xQFN28. By type, the board carries 19 capacitors, 12 resistors, 6 ICs, 5 diodes, 4 connectors and 3 switches.
From the project
KIcad project from a CAN scanner based on ESP32

Main components on the Dongle Alive v2.0
Dongle Alive v2.0 bill of materials (BOM)
53 components, 26 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-WROOM-32 | ESP32-WROOM-32 | U1 |
| 1 | ~ | lm360_small | U2 |
| 1 | AMS1117 | SOT-223-3_TabPin2 | U3 |
| 1 | TJA1050 | TJA1050T | U4 |
| 1 | MCP2515-I_SO | MCP2515 | U5 |
| 1 | CP2102N-Axx-xQFN28 | QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm | U6 |
| 2 | SS8050-G | TRANS_SS8050-G | Q2, Q3 |
| 1 | Crystal | Crystal_SMD_HC49-SD | Y1 |
| 1 | C-OBD-II-16M | COMTECH_C-OBD-II-16M | J1 |
| 2 | Conn_01x07 | JST_EH_B7B-EH-A_1x07_P2.50mm_Vertical | J2, J3 |
| 1 | USB_B_Micro | USB_Micro-B_Molex_47346-0001 | J4 |
| 1 | 0.5A | Fuseholder_Clip-5x20mm_Littelfuse_111_Inline_P20.00x5.00mm_D1.05mm_Horizontal | F1 |
| 2 | SW_Push | SW_SPST_CK_RS282G05A3 | SW1, SW2 |
| 1 | SW_SPDT_321 | SW_Slide-03_Wuerth-WS-SLTV_10x2.5x6.4_P2.54mm | SW3 |
| 3 | LED | LED_0805_2012Metric | D1, D2, D5 |
| 1 | PESD1CAN | PESD1CAN | D6 |
| 1 | BAT760-7 | BAT760-7 | D7 |
| 1 | 22uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1 |
| 8 | 10uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C4, C7, C12, C13, C20, C21, C22 |
| 7 | 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C5, C8, C14, C15, C17, C23 |
Show 6 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 10uF | CP_EIA-2012-12_Kemet-R_Pad1.30x1.05mm_HandSolder | C16 |
| 2 | 22pF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C18, C19 |
| 5 | 10kΩ | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R15, R18, R19 |
| 2 | 1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R4 |
| 4 | 120Ω | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R6, R14, R16 |
| 1 | 1kΩ | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R17 |
Dongle Alive v2.0 design files
The KiCad project lives in the AntonioSilva584/Dongle_Alive_v2.0 repository on GitHub; these links point at the commit this page was built from.
- LayoutDongleALIVEv2.0.kicad_pcb
- SchematicDongleALIVEv2.0.kicad_sch
Dongle Alive v2.0: common questions
What microcontroller does the Dongle Alive v2.0 use?
The Dongle Alive v2.0 is built around the ESP32-WROOM-32, from the ESP32 family.
How big is the Dongle Alive v2.0 PCB?
The Dongle Alive v2.0 measures 45 × 55 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Dongle Alive v2.0?
53 components, from 26 distinct parts. The full bill of materials is listed on this page.
Where can I download the Dongle Alive v2.0 design files?
From the AntonioSilva584/Dongle_Alive_v2.0 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Dongle Alive v2.0 design in my own project?
The repository has no license, so all rights stay with AntonioSilva584. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Dongle Alive v2.0 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k