21 open source boards using the TJA1050
Real designs built with the TJA1050, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
SimpleFC G
wangyeee
42 × 50 mm130 parts4LBSD-3-Clause9ESP32
Esp32-c3-board bms
ieb
94.9 × 40.6 mm39 parts2LNo license2AVR/Arduino
EngineManagementSimpleWithMosfets
ieb
150 × 100 mm147 parts2LNo license1STM32
DaisyStepperDriver
MarginallyClever
64 × 92.8 mm91 parts4LNo license1ESP32
KIA-OBD2-DISPLAY
dragonnn
99.8 × 19.6 mm72 parts4LMIT1ESP32
Dongle eaLIVE
joaogabrielsantosD
45 × 55 mm69 parts2LNo license1STM32
Board
myhomecan
32 × 96 mm89 parts2LNo license0ESP32
Dongle Alive v2.0
AntonioSilva584
45 × 55 mm53 parts4LNo license0Kicad board-2026-07-27-bluepillcomnode
SimulatedFlow
100 × 80 mm22 parts4LCustom license0STM32
SimpleFCv2
wangyeee
42 × 50 mm119 parts4LBSD-3-Clause9ESP32
ESP32CanBoard
ieb
73.2 × 69.1 mm30 parts2LNo license2Display mit raspiZ
jstrebel
140 × 90.5 mm49 parts2LNo license1STM32
Tinyfc core
wangyeee
36 × 44 mm103 parts4LBSD-3-Clause9ESP32
Esp32-c3-board
ieb
94.9 × 40.6 mm28 parts2LNo license2ESP32
Esp32-c3-board waveshare
ieb
118.7 × 40.6 mm26 parts2LNo license2AVR/Arduino
EngineManagement
ieb
97 × 56.1 mm59 parts2LNo license1STM32
LoRaModem
wangyeee
24 × 36 mm48 parts2LBSD-3-Clause9Raspberry Pi
PiCanBoard
ieb
106.7 × 61.6 mm45 parts2LNo license1STM32
AirSeneor
wangyeee
45 × 30 mm39 parts2LBSD-3-Clause9Nucleo F446Shield v2
SamsonChau
85 × 97.4 mm47 parts2LNo license0- schematic only · 234 partsSTM32
Fx3u 24mr
eddyem
234 parts2LNo license208
How designs wire the TJA1050
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the TJA1050 connects to, and the resistors, capacitors and other passives placed on it.
- The VREF pin is left unconnected on 10 of 11 designs.
- The VCC pin has a decoupling capacitor on 8 of 11 designs, most often 100 nF (then 10 µF).
- The CANH pin has a series resistor on 8 of 11 designs, most often 120 Ω.
- The S pin is tied to GND on 9 of 11 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 2 | Connected to: GND 100% | — |
| VCCpin 3 | Connected to: 5V 73% · a signal 27% |
|
| VREFpin 5 | Connected to: Not connected 91% | — |
| CANLpin 6 | Connected to: A connector 91% |
|
| CANHpin 7 | Connected to: A connector 91% |
|
| Spin 8 | Connected to: GND 82% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include AirSeneor by wangyeee, Esp32-c3-board by ieb, KIA-OBD2-DISPLAY by dragonnn and EngineManagement by ieb.
The TJA1050 in open source designs
The gallery holds 21 open source boards using the TJA1050 from 12 GitHub repositories; a typical one measures about 79.1 × 55 mm and carries around 53 components.
67% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.
The most starred is Fx3u 24mr by eddyem.
Parts used alongside the TJA1050
Microcontrollers on boards using the TJA1050
What boards using the TJA1050 are built for
TJA1050: common questions
Where can I find a TJA1050 reference design?
Each of the 21 boards on this page is a real design using the TJA1050. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TJA1050 VREF pin connected?
The VREF pin is left unconnected on 10 of 11 designs. Counted from the KiCad layouts of 11 open source designs using the TJA1050.
What decoupling capacitors do designs use on the TJA1050 VCC pin?
The VCC pin has a decoupling capacitor on 8 of 11 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 11 open source designs using the TJA1050.
What resistor goes on the TJA1050 CANH pin?
The CANH pin has a series resistor on 8 of 11 designs, most often 120 Ω. Counted from the KiCad layouts of 11 open source designs using the TJA1050.
What parts are used alongside the TJA1050?
The 74HC4051, AMS1117, AMS1117-3.3, CP2102N-Axx-xQFN28 and ESP32-WROOM-32 appear in the most repositories here.
Which microcontrollers do boards using the TJA1050 use?
Most are built on STM32 (8), ESP32 (7), AVR/Arduino (2) and Raspberry Pi (1).
How big is a typical board using the TJA1050?
The median is 79.1 × 55 mm, and 67% are two-layer designs.
What is the most popular open source board using the TJA1050?
By GitHub stars, Fx3u 24mr by eddyem, with 208 stars.
Can I simulate one of these boards using the TJA1050 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.