10 open source boards using the MCP2515-I/SO
Real designs built with the MCP2515-I/SO, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Quiver PT3 Main PCB-rounded
Arrow-air
235.1 × 213.7 mm157 parts6LCERN-OHL-S-2.0492AVR/Arduino
MDE22
ZeniteSolar
144 × 59.5 mm69 parts2LNo license2ESP32
Dongle eaLIVE
joaogabrielsantosD
45 × 55 mm69 parts2LNo license1AVR/Arduino
Vehicle controL module 0.1.0
WATonomous
2.5 × 2.5 mm65 parts2LNo license1STM32
Impeller18
buglalis
236.1 × 156.9 mm750 parts4LNo license0AVR/Arduino
BlinCAN
metalhead777
127.1 × 67.1 mm84 parts2LCC-BY-SA-4.00ESP32
Dongle Alive v2.0
AntonioSilva584
45 × 55 mm53 parts4LNo license0CMAIN
Arrow-air
210.6 × 220 mm245 parts4LCERN-OHL-S-2.0175AVR/Arduino
Sensor interface 1.1.0
WATonomous
68.6 × 53.3 mm60 parts2LNo license1AVR/Arduino
Gateway r0
WATonomous
68.6 × 53.3 mm59 parts2LNo license1
How designs wire the MCP2515-I/SO
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the MCP2515-I/SO connects to, and the resistors, capacitors and other passives placed on it.
- The OSC2 pin has a crystal on 8 of 8 designs, most often 16 MHz.
- The OSC2 pin has a capacitor to GND on 8 of 8 designs, most often 22 pF (then 8 pF).
- The RESET pin has a pull-up to 5V on 8 of 8 designs, most often 10 kΩ (then 1 kΩ).
- The OSC1 pin has a crystal on 7 of 8 designs, most often 16 MHz.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CLKOUT/SOFpin 3 | Connected to: Not connected 100% | — |
| TX0RTSpin 4 | Connected to: Not connected 100% | — |
| TX1RTSpin 5 | Connected to: Not connected 100% | — |
| TX2RTSpin 6 | Connected to: Not connected 100% | — |
| OSC2pin 7 | Connected to: Signal 100% |
|
| OSC1pin 8 | Connected to: Signal 100% |
|
| VSSpin 9 | Connected to: GND 100% | — |
| RX1BFpin 10 | Connected to: Not connected 100% | — |
| RX0BFpin 11 | Connected to: Not connected 100% | — |
| RESETpin 17 | Connected to: Signal 100% |
|
| VDDpin 18 | Connected to: 5V 100% |
|
7 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Quiver PT3 Main PCB-rounded by Arrow-air, CMAIN PCB by Arrow-air, MDE22 by ZeniteSolar and Dongle eaLIVE-PCB by joaogabrielsantosD.
The MCP2515-I/SO in open source designs
The gallery holds 10 open source boards using the MCP2515-I/SO from 8 GitHub repositories; a typical one measures about 97.8 × 57.2 mm and carries around 69 components.
60% are two-layer designs, the rest use four layers or more, and 30% carry an open source license.
The most starred is Quiver PT3 Main PCB-rounded by Arrow-air.
Parts used alongside the MCP2515-I/SO
Microcontrollers on boards using the MCP2515-I/SO
What boards using the MCP2515-I/SO are built for
MCP2515-I/SO: common questions
Where can I find a MCP2515-I/SO reference design?
Each of the 10 boards on this page is a real design using the MCP2515-I/SO. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MCP2515-I/SO OSC2 pin connected?
The OSC2 pin has a crystal on 8 of 8 designs, most often 16 MHz. Counted from the KiCad layouts of 8 open source designs using the MCP2515-I/SO.
What pull-up resistor is used on the MCP2515-I/SO RESET pin?
The RESET pin has a pull-up to 5V on 8 of 8 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 8 open source designs using the MCP2515-I/SO.
How is the MCP2515-I/SO OSC1 pin connected?
The OSC1 pin has a crystal on 7 of 8 designs, most often 16 MHz. Counted from the KiCad layouts of 8 open source designs using the MCP2515-I/SO.
What parts are used alongside the MCP2515-I/SO?
The AMS1117, CP2102N-Axx-xQFN28, ESP32-WROOM-32, MCP2551-I-SN and SMTSOM380BTR appear in the most repositories here.
Which microcontrollers do boards using the MCP2515-I/SO use?
Most are built on AVR/Arduino (5), ESP32 (2) and STM32 (1).
How big is a typical board using the MCP2515-I/SO?
The median is 97.8 × 57.2 mm, and 60% are two-layer designs.
What is the most popular open source board using the MCP2515-I/SO?
By GitHub stars, Quiver PT3 Main PCB-rounded by Arrow-air, with 492 stars.
Can I simulate one of these boards using the MCP2515-I/SO before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.