PhantomPod
AoujHaider-maker·PhantomPod·PCB/DCD.kicad_pcb
About the PhantomPod PCB
PhantomPod is an open source ESP32 PCB design by AoujHaider-maker, published on GitHub. It is a 2-layer board measuring 80 × 125 mm, with 60 components from 38 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the USBLC6-2SC6, TPA6132A2RTE, AP2112K-3.3 and MCP73831-2-OT. By type, the board carries 15 capacitors, 10 resistors, 8 connectors, 8 switches, 8 diodes and 5 ICs.
It belongs with the audio, displays & leds and power & battery designs in this gallery.
From the project
An ESP32-S3 cassette player designed to bring the tactile experience of physical media back to modern music.
PhantomPod is a pocket digital cassette player built around an ESP32-S3. You slot in a vertical cassette-shaped cartridge that holds a microSD card and an NFC tag. Spring-loaded pogo pins read its six gold contacts, and the player recognizes it automatically. It has a 2.23" 128×32 OLED, 12 underglow RGB LEDs, a side rotary encoder and buttons, two headphone jacks driven by a PCM5102A DAC and TPA6132A2 amp, and USB-C LiPo charging. I designed the whole 80×125 mm 2-layer PCB in KiCad (schematic, layout, DRC/ERC clean), exported the Gerbers and BOM, and wrote a PlatformIO bring-up firmware…
Main components on the PhantomPod
PhantomPod bill of materials (BOM)
60 components, 38 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U2 |
| 1 | TPA6132A2RTE | WQFN-16-1EP_3x3mm_P0.5mm_EP1.6x1.6mm_ThermalVias | U3 |
| 1 | AP2112K-3.3 | SOT-23-5 | U4 |
| 1 | MCP73831-2-OT | SOT-23-5 | U5 |
| 3 | AO3401A | SOT-23 | Q1, Q3, Q4 |
| 2 | 2N7002 | SOT-23 | Q2, Q5 |
| 1 | USB_C_RECEPTACLE_USB2.0_16P USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | CONN_01X04 Conn_01x04 | PinSocket_1x04_P2.54mm_Vertical | J3 |
| 1 | CONN_01X08 Conn_01x08 | PinSocket_1x08_P2.54mm_Vertical | J4 |
| 1 | CONN_01X06 Conn_01x06 | PinSocket_1x06_P2.54mm_Vertical | J5 |
| 2 | AUDIOJACK3 AudioJack3 | Jack_3.5mm_CUI_SJ1-3523N_Horizontal | J6, J7 |
| 1 | CONN_01X03 Conn_01x03 | PinSocket_1x03_P2.54mm_Vertical | J9 |
| 1 | CONN_01X06 Conn_01x06 | PinHeader_1x06_P2.54mm_Vertical | J10 |
| 1 | Battery_Cell | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | BT1 |
| 1 | RESET | SW_SPST_B3U-3000P | SW1 |
| 1 | SW_SPDT | SW_SPDT_PCM12 | SW2 |
| 1 | BOOT | SW_SPST_B3U-3000P | SW3 |
| 1 | FF | SW_SPST_B3U-3000P | SW4 |
| 1 | RotaryEncoder_Switch | RotaryEncoder_Bourns_Horizontal_PEC09-2xxxF-Sxxxx | SW5 |
Show 18 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | BACK | SW_SPST_B3U-3000P | SW6 |
| 1 | PLAY | SW_SPST_B3U-3000P | SW7 |
| 1 | SETUP | SW_SPST_B3U-3000P | SW8 |
| 1 | LED | LED_0603_1608Metric | D1 |
| 7 | SK6812MINI | LED_SK6812MINI_PLCC4_3.5x3.5mm_P1.75mm | D2, D3, D4, D5, D6, D8, D11 |
| 1 | 10UF 10uF | C_0603_1608Metric | C1 |
| 1 | 0.1UF 0.1uF | C_0603_1608Metric | C2 |
| 6 | 1UF 1uF | C_0603_1608Metric | C3, C6, C7, C9, C11, C12 |
| 2 | 4.7UF 4.7uF | C_0805_2012Metric | C4, C5 |
| 3 | 2.2UF 2.2uF | C_0805_2012Metric | C8, C13, C14 |
| 1 | 10 µF | C_0805_2012Metric | C10 |
| 1 | 100 µF | C_1210_3225Metric | C15 |
| 1 | 10K 10k | R_0603_1608Metric | R1 |
| 2 | 5.1K 5.1k | R_0603_1608Metric | R2, R3 |
| 1 | 2k | R_0603_1608Metric | R4 |
| 1 | 1k | R_0603_1608Metric | R5 |
| 4 | 100 kΩ | R_0603_1608Metric | R7, R8, R9, R10 |
| 1 | 330 | R_0603_1608Metric | R11 |
PhantomPod design files
The KiCad project lives in the AoujHaider-maker/PhantomPod repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/DCD.kicad_pcb
- SchematicPCB/DCD.kicad_sch
- BOMProduction/DCD.csv
PhantomPod: common questions
What microcontroller does the PhantomPod use?
The PhantomPod is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the PhantomPod PCB?
The PhantomPod measures 80 × 125 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the PhantomPod?
60 components, from 38 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the PhantomPod design files?
From the AoujHaider-maker/PhantomPod repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the PhantomPod design in my own project?
The repository has no license, so all rights stay with AoujHaider-maker. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the PhantomPod without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k