Before hole repair
apws·261108-retro-comp-andrew-codex-kicad·reports/firstz80/03-freerouting/native-attempt-02/before-hole-repair.kicad_pcb
About the Before hole repair PCB
Before hole repair is an open source PCB design by apws, published on GitHub. It is a 2-layer board measuring 160 × 100 mm, with 62 components from 36 distinct parts.
Other key parts include the 74LS14, Z80CPU, 74LS32, KM62256CLP and 8255. By type, the board carries 19 capacitors, 14 resistors, 10 diodes, 9 ICs, 4 connectors and 2 crystals.
It belongs with the retro computing designs in this gallery.
From the project
Andrew Z80 KiCad comparison: schematic, shared Eurocard placement, and three verified headless routing experiments
Main components on the Before hole repair
Before hole repair bill of materials (BOM)
62 components, 36 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 74LS14 | Package_DIP__DIP-14_W7.62mm_Socket_LongPads | U1 |
| 1 | Z80CPU | Package_DIP__DIP-40_W15.24mm_Socket_LongPads | U2 |
| 1 | 74LS32 | Package_DIP__DIP-14_W7.62mm_Socket_LongPads | U3 |
| 1 | KM62256CLP | Package_DIP__DIP-28_W15.24mm_Socket_LongPads | U4 |
| 1 | 8255 | Package_DIP__DIP-40_W15.24mm_Socket_LongPads | U5 |
| 1 | 28C256 | Package_DIP__DIP-28_W15.24mm_Socket_LongPads | U6 |
| 1 | 16550 | Package_DIP__DIP-40_W15.24mm_Socket_LongPads | U7 |
| 1 | MAX232 | Package_DIP__DIP-16_W7.62mm_Socket_LongPads | U8 |
| 1 | LM7805_TO220 | Package_TO_SOT_THT__TO-220-3_Horizontal_TabDown | U9 |
| 1 | CLK-CPU | Oscillator__Oscillator_DIP-14 | X1 |
| 1 | CLK-UART | Oscillator__Oscillator_DIP-14 | X2 |
| 1 | Barrel_Jack_MountingPin | Connector_BarrelJack__BarrelJack_Horizontal | J1 |
| 1 | TTL SERIAL | Connector_PinHeader_2.54mm__PinHeader_1x06_P2.54mm_Horizontal | J2 |
| 1 | 9VDC | TerminalBlock_Phoenix__TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J4 |
| 1 | PPI | Connector_IDC__IDC-Header_2x13_P2.54mm_Horizontal | P1 |
| 1 | PPI PWR | Connector_PinHeader_2.54mm__PinHeader_1x03_P2.54mm_Vertical | K1 |
| 1 | RESET | Button_Switch_THT__SW_PUSH_6mm | SW1 |
| 1 | VCC | Connector_PinHeader_2.54mm__PinHeader_1x01_P2.54mm_Vertical | TP1 |
| 1 | GND | Connector_PinHeader_2.54mm__PinHeader_1x01_P2.54mm_Vertical | TP2 |
| 1 | POWER | LED_THT__LED_D3.0mm | D1 |
Show 16 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | RX | LED_THT__LED_D3.0mm | D2 |
| 1 | TX | LED_THT__LED_D3.0mm | D3 |
| 1 | PPI | LED_THT__LED_D3.0mm | D4 |
| 1 | RAM | LED_THT__LED_D3.0mm | D5 |
| 1 | ROM | LED_THT__LED_D3.0mm | D6 |
| 1 | UART | LED_THT__LED_D3.0mm | D7 |
| 1 | OUT1 | LED_THT__LED_D3.0mm | D8 |
| 1 | OUT2 | LED_THT__LED_D3.0mm | D9 |
| 1 | 1N5819 | Diode_THT__D_DO-41_SOD81_P10.16mm_Horizontal | D10 |
| 4 | 10uF | Capacitor_THT__CP_Radial_D5.0mm_P2.50mm | C1, C15, C16, C17 |
| 5 | 1uF | Capacitor_THT__CP_Radial_D5.0mm_P2.50mm | C2, C3, C4, C5, C6 |
| 9 | 0.1u | Capacitor_THT__C_Disc_D5.0mm_W2.5mm_P5.00mm | C7, C8, C9, C10, C11, C12, C13, C18 +1 |
| 1 | 0.1uF | Capacitor_THT__C_Disc_D5.0mm_W2.5mm_P5.00mm | C14 |
| 3 | 10K | Resistor_THT__R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3 |
| 1 | 10 | Resistor_THT__R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4 |
| 10 | 470 | Resistor_THT__R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R5, R6, R7, R8, R9, R10, R11, R12 +2 |
Before hole repair design files
The KiCad project lives in the apws/261108-retro-comp-andrew-codex-kicad repository on GitHub; these links point at the commit this page was built from.
Before hole repair: common questions
How big is the Before hole repair PCB?
The Before hole repair measures 160 × 100 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Before hole repair?
62 components, from 36 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Before hole repair design files?
From the apws/261108-retro-comp-andrew-codex-kicad repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Before hole repair design in my own project?
The repository has no license, so all rights stay with apws. Use it as a reference, and ask the author before reusing the design.
More boards in 261108-retro-comp-andrew-codex-kicad
Similar boards
Expansion Card Retrofit
FrameworkComputer
24 × 27.3 mm5 parts2LCC-BY-4.01.1kRgb to hdmi
hoglet67
77 × 97 mm67 parts2LGPL-3.01.0kBuffer
hoglet67
53.9 × 23.2 mm13 parts2LGPL-3.01.0kX1
hoglet67
121.9 × 81.3 mm51 parts2LGPL-3.01.0kAmiga External
hoglet67
21.9 × 76.7 mm6 parts2LGPL-3.01.0kVideoslotadapter
hoglet67
152 × 57.6 mm13 parts2LGPL-3.01.0k