Pic dev board

bablokb·pcb-pic-devboard·pic-dev-board.kicad/pic-dev-board.kicad_pcb

Pic dev board layout, top view — open source PIC board by bablokb

About the Pic dev board

Pic dev board is an open source PIC PCB design by bablokb, published on GitHub under the CC-BY-SA-4.0 license. It is a 2-layer board measuring 100 × 100 mm, with 73 components from 39 distinct parts.

Its main chip is the PIC16F1829-IP, from the PIC family. Other key parts include the AMS1117-33, 74HC595, SO-8-ProtoArea and SOT-223-ProtoArea. By type, the board carries 24 connectors, 22 diodes, 19 resistors, 5 ICs, 1 switch and 1 capacitor.

It belongs with the dev boards & breakouts designs in this gallery.

From the project

Development board for PIC12/PIC16 microcontrollers

Development board for PIC12/PIC16 microcontrollers ==================================================

This repository contains the design-files (Kicad) for three PIC12/PIC16 development boards.

This is a full sized dev-board, see directory pic-dev-board.kicad:

- a PIC12 or a 20-pin PIC16 - configurable pullups or LEDs on GP0-GP5 - two shift-registers with LEDs to output 8-16 bits using two GPs (see project pic-sn74hc595) - a LCD1602 attached to the first shift-register (see project pic-hd44780_lcd) - ICSP programming - all pins broken out to connectors (TRISB/TRISC only available for…

Pic dev board, from the project README
From the project README

Main components on the Pic dev board

PIC16F1829-IPAMS1117-3374HC595SO-8-ProtoAreaSOT-223-ProtoArea

Pic dev board bill of materials (BOM)

73 components, 39 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
PIC16F1829-IP
PIC16F690-IP
U1
1
AMS1117-33
74HC595
U2
1
74HC595
U3
1
SO-8-ProtoArea
U4
1
SOT-223-ProtoArea
U5
1
WC1602A
DS1
1
Conn_GP0
J1
1
APP_CONN_1
Conn_GP4
J2
1
APP_CONN_2
Conn_GP1
J3
1
Conn_GP5
J4
1
CONN_01X03_MALE
Conn_GP2
J5
1
CONN_BB1
Conn_ICSP
J6
1
CONN_01X03_MALE
Conn_TRISC
J7
2
Conn_TRISA
J8, J20
1
Conn_TRISB
J9
1
Jumper DATin
J10
1
Conn_SR_2
J11
1
Conn_SR_1
J12
1
Conn_5V_GND
J13
1
Jumper CLKin
J14
Show 19 more
QtyPartRefs
1
Barrel_Jack_Switch
J15
1
RUN/~PGM
J16
1
I2C
J17
1
GP1(RA1)/RB6
J18
1
GP2(RA2)/RB4
J19
2
Conn_01x04_Male
J21, J22
1
Conn_01x03_Male
J23
1
10K
RV1
1
SW_Push
SW1
1
C2296
LED
D1
1
C84256
LED
D2
19
LED
D3, D4, D5, D7, D8, D9, D10, D11 +11
1
D_Schottky
D6
1
100NF
100n
C1
7
4.7k
R1, R3, R5, R7, R9, R16, R17
8
1k
R2, R4, R6, R8, R10, R11, R13, R14
1
22k
R12
1
220
R15
2
680
RN1, RN2

Pic dev board design files

The KiCad project lives in the bablokb/pcb-pic-devboard repository on GitHub; these links point at the commit this page was built from.

Pic dev board: common questions

What microcontroller does the Pic dev board use?

The Pic dev board is built around the PIC16F1829-IP, from the PIC family.

How big is the Pic dev board?

The Pic dev board measures 100 × 100 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Pic dev board?

73 components, from 39 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Pic dev board design files?

From the bablokb/pcb-pic-devboard repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the Pic dev board design in my own project?

Yes, under the terms of its CC-BY-SA-4.0 license, which bablokb chose for the repository.

Can I test firmware for the Pic dev board without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.

More boards in pcb-pic-devboard

Similar boards