Oscillator Board
About the Oscillator Board
Oscillator Board is an open source AVR/Arduino PCB design by Bad-Dog-Designs, published on GitHub. It is a 2-layer board measuring 229 × 96 mm, with 132 components from 36 distinct parts.
Its main chip is the ATMEGA328P-A, from the AVR/Arduino family. Other key parts include the TJA1050T/CM,118, MCP2515T-I/ST, MCP23017-E/SO and CD74HC4067SM. By type, the board carries 53 resistors, 22 diodes, 16 switches, 16 capacitors, 6 ICs and 4 connectors.
It belongs with the audio and displays & leds designs in this gallery.
From the project
Source code and KiCad Files for the build of an ESP32 S3 Based synthesizer. CAN bus is used extensively to collect all the pots and switch data and send to the ESP32 engine
Project overview: A custom polyphonic synthesizer built around an ESP32-S3 audio engine communicating with multiple ATmega328p control boards via CAN bus at 500kbps. All boards share synth_params.h as the single source of truth for CAN message definitions. Hardware boards:
ESP32-S3 — audio engine, MIDI input, I2S DAC output, CAN master Oscillator boards (ATmega328p, up to 4) — dual oscillator control per board, board ID set by hardware jumpers (both open = board 0) Commons board (ATmega328p) — filter, envelope, LFO, ring mod, play mode controls Routing board (ATmega328p) — modulation matrix…
Main components on the Oscillator Board
Oscillator Board bill of materials (BOM)
132 components, 36 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TJA1050T/CM,118 TJA1050T_CM,118 | SOIC127P600X175-8N | IC1 |
| 1 | MCP2515T-I/ST MCP2515T-I_ST | SOP65P640X120-20N | IC2 |
| 2 | MCP23017-E/SO MCP23017-E_SO | SOIC127P1030X265-28N | IC3, IC4 |
| 1 | ATMEGA328P-A ATmega328P-A | TQFP-32_7x7mm_P0.8mm | U1 |
| 1 | CD74HC4067SM | SSOP-24_5.3x8.2mm_P0.65mm | U2 |
| 1 | 8MHZ 8Mhz | Crystal_HC49-4H_Vertical | Y1 |
| 1 | 16MHZ 16Mhz | Crystal_HC49-4H_Vertical | Y2 |
| 1 | ICP Header | PinSocket_2x03_P2.54mm_Vertical | J1 |
| 1 | Serial Mon | PinSocket_1x03_P2.54mm_Vertical | J2 |
| 1 | Output | JST_EH_S4B-EH_1x04_P2.50mm_Horizontal | J3 |
| 1 | Input | JST_EH_S4B-EH_1x04_P2.50mm_Horizontal | J4 |
| 1 | SR1712F-0108-20F0A-N9-N-027 Waveform_0 | SR1712F010820F0AN9N027 | S1 |
| 1 | SR1712F-0108-20F0A-N9-N-027 Range_0 | SR1712F010820F0AN9N027 | S2 |
| 1 | SR1712F-0108-20F0A-N9-N-027 Waveform_1 | SR1712F010820F0AN9N027 | S3 |
| 1 | SR1712F-0108-20F0A-N9-N-027 Range_1 | SR1712F010820F0AN9N027 | S4 |
| 12 | TL2285OA | TL2285OA | S5, S6, S7, S8, S9, S10, S11, S12 +4 |
| 2 | RK09K1130AAU Detune_1 | RK09K1130AAU | VR1, VR7 |
| 2 | RK09K1130AAU PulseW_1 | RK09K1130AAU | VR2, VR8 |
| 2 | RK09K1130AAU ChaosR_1 | RK09K1130AAU | VR3, VR9 |
| 2 | RK09K1130AAU Folds_1 | RK09K1130AAU | VR4, VR10 |
Show 16 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | RK09K1130AAU S&H_1 | RK09K1130AAU | VR5, VR11 |
| 2 | RK09K1130AAU Level_1 | RK09K1130AAU | VR6, VR12 |
| 22 | LED | LED_D3.0mm_FlatTop | D1, D2, D3, D4, D5, D6, D7, D8 +14 |
| 1 | 10R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | FB1 |
| 4 | 22PF 22pf | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C6, C7 |
| 7 | 100NF 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C4, C5, C8, C9, C10, C11 |
| 2 | 1UF 1uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C12, C13 |
| 1 | 4.7UF 4.7uF | CP_Radial_D4.0mm_P2.00mm | C14 |
| 1 | 100UF 100uF | CP_Radial_D4.0mm_P2.00mm | C15 |
| 1 | 10NF 10nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C16 |
| 4 | 10K 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R25, R29, R30 |
| 20 | 4K7 4k7 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, R3, R35, R36, R37, R38, R39, R40 +12 |
| 22 | 330R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4, R5, R6, R7, R8, R9, R10, R11 +14 |
| 2 | 1k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R24, R53 |
| 1 | 120R | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R28 |
| 4 | Link | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R31, R32, R33, R34 |
Oscillator Board design files
The KiCad project lives in the Bad-Dog-Designs/ESP32-S3-Synthesizer repository on GitHub; these links point at the commit this page was built from.
Oscillator Board: common questions
What microcontroller does the Oscillator Board use?
The Oscillator Board is built around the ATMEGA328P-A, from the AVR/Arduino family.
How big is the Oscillator Board?
The Oscillator Board measures 229 × 96 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Oscillator Board?
132 components, from 36 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Oscillator Board design files?
From the Bad-Dog-Designs/ESP32-S3-Synthesizer repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Oscillator Board design in my own project?
The repository has no license, so all rights stay with Bad-Dog-Designs. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Oscillator Board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in ESP32-S3-Synthesizer
Similar boards
AVR/ArduinoMagspoof
samyk
35 × 29 mm11 parts2LNo license4.2k
AVR/ArduinoRedox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0k
AVR/ArduinoLabrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2k
AVR/ArduinoV4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoModuleV450
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoDiscipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k