12 open source boards using the TJA1050T/CM,118
Real designs built with the TJA1050T/CM,118, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Oscillator Board
Bad-Dog-Designs
229 × 96 mm132 parts2LNo license18STM32
Monitor
zincVTD
62 × 35.4 mm48 parts2LNo license1AVR/Arduino
InverterBoostConverter
datacrystals
450 × 150 mm225 parts2LNo license0GD32
GD32-Devboard
ConnorRigby
50 × 79.5 mm82 parts4LNo license0ESP32
Suspension accel
meyerAurelius
20.6 × 74 mm38 parts4LNo license0AVR/Arduino
Routing Board
Bad-Dog-Designs
229 × 96 mm131 parts2LNo license18STM32
TPMS
zincVTD
62 × 47.2 mm47 parts2LNo license1ESP32
Version1
meyerAurelius
60 × 57.8 mm16 parts4LNo license0AVR/Arduino
Commons Board
Bad-Dog-Designs
229 × 96 mm95 parts2LNo license18AVR/Arduino
BDUCU
HKUST-Red-Bird-Racing-EVRT
140 × 60 mm169 parts2LNo license0AVR/Arduino
328 3ch can devboard
HKUST-Red-Bird-Racing-EVRT
82.8 × 55 mm68 parts2LNo license3AVR/Arduino
Front dash unit
HKUST-Red-Bird-Racing-EVRT
101 × 63.3 mm90 parts2LNo license0
How designs wire the TJA1050T/CM,118
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TJA1050T/CM,118 connects to, and the resistors, capacitors and other passives placed on it.
- The VREF pin is left unconnected on 7 of 7 designs.
- The VCC pin has a decoupling capacitor on 5 of 7 designs, most often 100 nF.
- The CANH pin has a series resistor on 5 of 7 designs, most often 120 Ω.
- The CANL pin has a series resistor on 4 of 7 designs, most often 120 Ω.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 2 | Connected to: GND 71% · a signal 29% | — |
| VCCpin 3 | Connected to: 5V 86% |
|
| VREFpin 5 | Connected to: Not connected 100% | — |
| CANLpin 6 | Connected to: A connector 86% |
|
| CANHpin 7 | Connected to: A connector 86% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Commons Board by Bad-Dog-Designs, 328 3ch can devboard by HKUST-Red-Bird-Racing-EVRT, TPMS by zincVTD and GD32-Devboard by ConnorRigby.
The TJA1050T/CM,118 in open source designs
The gallery holds 12 open source boards using the TJA1050T/CM,118 from 7 GitHub repositories; a typical one measures about 91.9 × 68.6 mm and carries around 86 components.
75% are two-layer designs, the rest use four layers or more, and 0% carry an open source license.
The most starred is Oscillator Board by Bad-Dog-Designs.
Parts used alongside the TJA1050T/CM,118
Microcontrollers on boards using the TJA1050T/CM,118
What boards using the TJA1050T/CM,118 are built for
TJA1050T/CM,118: common questions
Where can I find a TJA1050T/CM,118 reference design?
Each of the 12 boards on this page is a real design using the TJA1050T/CM,118. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TJA1050T/CM,118 VREF pin connected?
The VREF pin is left unconnected on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the TJA1050T/CM,118.
What decoupling capacitors do designs use on the TJA1050T/CM,118 VCC pin?
The VCC pin has a decoupling capacitor on 5 of 7 designs, most often 100 nF. Counted from the KiCad layouts of 7 open source designs using the TJA1050T/CM,118.
What resistor goes on the TJA1050T/CM,118 CANH pin?
The CANH pin has a series resistor on 5 of 7 designs, most often 120 Ω. Counted from the KiCad layouts of 7 open source designs using the TJA1050T/CM,118.
What parts are used alongside the TJA1050T/CM,118?
The 40106, ATMEGA328-A, ATmega328P-A, LTV-847S and MCP2515-XST appear in the most repositories here.
Which microcontrollers do boards using the TJA1050T/CM,118 use?
Most are built on AVR/Arduino (7), ESP32 (2), STM32 (2) and GD32 (1).
How big is a typical board using the TJA1050T/CM,118?
The median is 91.9 × 68.6 mm, and 75% are two-layer designs.
What is the most popular open source board using the TJA1050T/CM,118?
By GitHub stars, Oscillator Board by Bad-Dog-Designs, with 18 stars.
Can I simulate one of these boards using the TJA1050T/CM,118 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.