D1(Motherboard)

BenjaminJAnderson·CUBE·Hardware/PCB/D1(Motherboard)/D1(Motherboard).kicad_pcb

D1(Motherboard) PCB layout, top view — open source ESP32 board by BenjaminJAnderson

About the D1(Motherboard) PCB

D1(Motherboard) is an open source ESP32 PCB design by BenjaminJAnderson, published on GitHub under the MIT license. It is a 4-layer board measuring 38 × 35 mm, with 51 components from 27 distinct parts.

Its main chip is the ESP32-S2-MINI-1, from the ESP32 family. Other key parts include the ICM-20602, SSD1351, MIC5353-3.3YMT, FAN5331SX and MCP73831-2-OT. By type, the board carries 21 capacitors, 12 resistors, 6 ICs, 6 diodes, 3 connectors and 1 transistor.

It belongs with the displays & leds, power & battery and iot & wireless designs in this gallery.

From the project

CUBE is a miniature, six-faced OLED display cube built from a stack of custom interconnected PCBs. The current design combines an ESP32-S2 motherboard, five further display boards, a magnet-held 3D-printed frame and bring-up firmware for SPI displays and motion sensing.

CUBE is a miniature, six-faced OLED display cube built from a stack of custom interconnected PCBs. The current design combines an ESP32-S2 motherboard, five further display boards, a magnet-held 3D-printed frame and bring-up firmware for SPI displays and motion sensing.

CUBE is a handheld, self-contained display object rather than a conventional LED matrix. Each of its six faces carries a 1.5-inch, 128×128 RGB OLED module driven by an SSD1351 controller, giving 98,304 addressable pixels across the cube. The aim is to make a small object whose faces can show independent graphics and respond…

D1(Motherboard), from the project README
From the project README

Main components on the D1(Motherboard)

D1(Motherboard) bill of materials (BOM)

51 components, 27 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-S2-MINI-1
U1
1
ICM-20602
U2
1
SSD1351
U3
1
MIC5353-3.3YMT
U4
1
FAN5331SX
U5
1
MCP73831-2-OT
U6
1
NX2301P.215
Q1
1
WR-FPC_0.5mm_ZIF_V
J1
1
USB_C_Receptacle_USB2.0
J2
1
B2B-PH-K-S
J3
1
CHS-02A
SW1
2
1N4148WS-7-F
D1, D2
2
GREEN
D3, D6
1
BAT54GWJ
D4
1
BATG54GWJ
D5
1
SRR4028-100Y
L1
5
4.7u
C1, C9, C14, C18, C20
9
0.1u
C2, C3, C7, C10, C11, C12, C13, C16 +1
2
10u
C4, C8
1
4.7u
C5
Show 7 more
QtyPartRefs
4
1u
C6, C15, C17, C21
3
10k
R1, R6, R8
1
2k
R2
2
1k
R3, R12
1
47R
R4
1
560k
R5
4
100k
R7, R9, R10, R11

D1(Motherboard) design files

The KiCad project lives in the BenjaminJAnderson/CUBE repository on GitHub; these links point at the commit this page was built from.

D1(Motherboard): common questions

What microcontroller does the D1(Motherboard) use?

The D1(Motherboard) is built around the ESP32-S2-MINI-1, from the ESP32 family.

How big is the D1(Motherboard) PCB?

The D1(Motherboard) measures 38 × 35 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the D1(Motherboard)?

51 components, from 27 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the D1(Motherboard) design files?

From the BenjaminJAnderson/CUBE repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the D1(Motherboard) design in my own project?

Yes, under the terms of its MIT license, which BenjaminJAnderson chose for the repository.

Can I test firmware for the D1(Motherboard) without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in CUBE

Similar boards