Env

bread-modular·bread-modular·modules/env/env.kicad_pcb

Env PCB layout, top view — open source AVR/Arduino board by bread-modular

About the Env PCB

Env is an open source AVR/Arduino PCB design by bread-modular, published on GitHub under the MIT license. It is a 2-layer board measuring 30.5 × 68.6 mm, with 29 components from 15 distinct parts.

Its main chip is the ATTINY1616-M, from the AVR/Arduino family. Other key parts include the MCP6002-XSN. By type, the board carries 12 resistors, 3 ICs, 3 diodes, 3 capacitors, 2 connectors and 2 switches.

It belongs with the audio designs in this gallery.

From the project

Modular Synths for Everyone

Modular Design: Just like Eurorack USB-Powered: It can be portable Minimal Design: Cost Effective Modular MIDI Support: Use MIDI to communicate between modules (still supports CV & Gate) Analog and Digital Signal Paths: It’s your choice Diverse Built-in Modules: Includes a wide range of pre-designed modules Configurable Digital Modules: Supports both voice and CV (uses AtTiny 1616 or ESP32) Fully Open Source: Including schematics, PCB designs, and code Ease of Customization: Enables straightforward creation of custom modules tailored to specific needs. No Case Required: Can be used directly…

Env, from the project README
From the project README

Main components on the Env

Env bill of materials (BOM)

29 components, 15 distinct parts — part numbers from the project's BOM.

QtyPartRefs
2
MCP6002-XSN
MCP6002-xSN
U1, U3
1
ATTINY1616-M
ATtiny1616-M
U2
1
CONN_01X05_PIN
Conn_01x05_Pin
GND1
1
Conn_01x05_Pin
V_SUPPLY1
1
CONN_01X05_SOCKET
Conn_01x05_Socket
INPUT1
1
CONN_01X05_SOCKET
Conn_01x05_Socket
OUTPUT1
2
1M
RV2, RV3
2
K2-1808SN-A4SW-01
SW1, SW2
3
LED
D1, D2, D3
1
100UF
100uf
C1
2
0.1UF
0.1uf
C3, C4
2
4.7K
4.7k
R1, R12
3
1k
R2, R4, R5
5
100K
100k
R3, R7, R8, R10, R11
2
330
R6, R9

Env design files

The KiCad project lives in the bread-modular/bread-modular repository on GitHub; these links point at the commit this page was built from.

Env: common questions

What microcontroller does the Env use?

The Env is built around the ATTINY1616-M, from the AVR/Arduino family.

How big is the Env PCB?

The Env measures 30.5 × 68.6 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Env?

29 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Env design files?

From the bread-modular/bread-modular repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Env design in my own project?

Yes, under the terms of its MIT license, which bread-modular chose for the repository.

Can I test firmware for the Env without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in bread-modular

Similar boards