Imu splitter
About the Imu splitter PCB
Imu splitter is an open source PCB design by BUNPC, published on GitHub. It is a 2-layer board measuring 54 × 54 mm, with 16 components from 10 distinct parts.
Other key parts include the AP2114H-3.3TRG1. By type, the board carries 9 connectors, 2 diodes, 2 capacitors, 2 resistors and 1 IC.
It belongs with the sensors designs in this gallery.
From the project
Repository for the storage and dissemination of NN22 technical documents
All IMU electronics files are located in this folder.
There is not a dedicated IMU backboard part as the IMU interface cards are intended to be used with the existing detector backplanes in place of a detector interface card.
Main components on the Imu splitter
Imu splitter bill of materials (BOM)
16 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AP2114H-3.3TRG1 | SOT-223-3_TabPin2 | U1 |
| 6 | 4P4C | A-2004-3-4-LP | J1, J2, J3, J4, J5, J6 |
| 1 | 3220-26-0200-00 | SAMTEC_SHF-113-01-L-D-RA | J7 |
| 1 | CONN_01X04 Conn_01x04 | PinHeader_1x04_P1.27mm_Vertical | J8 |
| 1 | CONN_01X05 Conn_01x05 | PinHeader_1x05_P2.54mm_Vertical | J9 |
| 2 | LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2 |
| 1 | 10UF 10uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1 |
| 1 | 22UF 22uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2 |
| 1 | 1.5K 1.5k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 510 | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | R2 |
Imu splitter design files
The KiCad project lives in the BUNPC/NN22-Technical-Documents repository on GitHub; these links point at the commit this page was built from.
Imu splitter: common questions
How big is the Imu splitter PCB?
The Imu splitter measures 54 × 54 mm, has 2 copper layers and is 1.5748 mm thick.
How many components are on the Imu splitter?
16 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Imu splitter design files?
From the BUNPC/NN22-Technical-Documents repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Imu splitter design in my own project?
The repository has no license, so all rights stay with BUNPC. Use it as a reference, and ask the author before reusing the design.
More boards in NN22-Technical-Documents
Similar boards
Sensor smd
scottbez1
40 × 20 mm5 parts2LApache-2.04.2k
Sensors
StuckAtPrototype
15.2 × 9 mm14 parts4LApache-2.03.8k
Microphone
Mentra-Community
5.5 × 6.1 mm6 parts2LMIT1.2k
TemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1k
Pots
shanteacontrols
390 × 93 mm75 parts2LApache-2.0956
USB
52 × 12.6 mm6 parts2LApache-2.0956