Custom-STM32

dhnz-2006·Custom-STM32-Kicad

Custom-STM32 PCB layout, top view — open source STM32 board by dhnz-2006

About the Custom-STM32 PCB

Custom-STM32 is an open source STM32 PCB design by dhnz-2006, published on GitHub. It is a 2-layer board measuring 52 × 52 mm, with 37 components from 26 distinct parts.

Its main chip is the STM32F030C8Tx, from the STM32 family. Other key parts include the 4u7, 100n, 8MHz, 30p and 10p. By type, the board carries 15 ICs, 11 resistors, 4 diodes, 3 connectors, 2 switches and 1 inductor.

It belongs with the dev boards & breakouts designs in this gallery.

From the project

Custom Made STM32 Microcontroller Using Kicad

This project contains the KiCad design files and documentation for a custom microcontroller development board based on the STM32F030 series MCU. The board is designed for low-cost embedded systems and prototyping.

- Microcontroller: STM32F030F4P6 (ARM Cortex-M0, 48MHz, 16KB Flash, 4KB RAM) - Power Supply: 3.3V regulated via AMS1117-3.3 or LDO (external 5V input) - Programming Interface: SWD (via ST-Link or similar) - Onboard Peripherals: - User LED (GPIO) - Tactile Reset & Boot buttons - Decoupling capacitors - crystal oscillator (8MHz) - IO Pins: All GPIOs exposed on 2.54mm headers - Form…

Custom-STM32, from the project README
From the project README

Main components on the Custom-STM32

Custom-STM32 bill of materials (BOM)

37 components, 26 distinct parts.

QtyPartRefs
1
4u7
U1
6
100n
U2, U3, U4, U5, U6, U12
1
8MHz
U7
2
30p
U8, U9
1
STM32F030C8Tx
U10
1
10p
U11
1
10n
U13
1
TPS5430DDA
U14
1
10u
U15
2
Communication pins
J1, J2
1
5V-20V
J4
2
SW_Push
SW1, SW2
1
LED1
D1
1
LED2
D2
1
B340
D3
1
PWR Status
D4
1
15uH
L1
1
220u
C1
3
1k5
R1, R2, R8
1
10K
R3
Show 6 more
QtyPartRefs
2
2k2
R4, R5
1
1K
R6
1
100K
R7
1
8k2
R9
1
1k5
R10
1
2k7
R11

Custom-STM32 design files

The KiCad project lives in the dhnz-2006/Custom-STM32-Kicad repository on GitHub; these links point at the commit this page was built from.

Custom-STM32: common questions

What microcontroller does the Custom-STM32 use?

The Custom-STM32 is built around the STM32F030C8Tx, from the STM32 family.

How big is the Custom-STM32 PCB?

The Custom-STM32 measures 52 × 52 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Custom-STM32?

37 components, from 26 distinct parts. The full bill of materials is listed on this page.

Where can I download the Custom-STM32 design files?

From the dhnz-2006/Custom-STM32-Kicad repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Custom-STM32 design in my own project?

The repository has no license, so all rights stay with dhnz-2006. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Custom-STM32 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards