7 open source boards using the 100N
Real designs built with the 100N, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
GPS-Tracker
mohamedboubaker
35 × 53 mm53 parts2LNo license40STM32
GPS-Tracker
ibfarhat
35 × 53 mm53 parts2LNo license3STM32
Custom-STM32-PCB-With
mohamedboubaker
52 × 52 mm37 parts2LNo license2STM32
GPS-Tracker
HarshBihani18
35 × 53 mm53 parts2LNo license0STM32
Pcb nixie
fernandezdelpeloso
90.7 × 90.7 mm44 parts6LNo license0STM32
Custom-STM32
dhnz-2006
52 × 52 mm37 parts2LNo license0Freq Gen MCU
joemadeus
80 × 39 mm46 parts2LNo license1
How designs wire the 100N
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the 100N connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 is tied to 3.3V on 5 of 6 designs.
- Pin 2 is tied to GND on 5 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: 3.3V 83% · GND 17% | — |
| Pin 2 | Connected to: GND 83% · VDD 17% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include GPS-Tracker by mohamedboubaker, GPS-Tracker by ibfarhat, Custom-STM32-PCB-With-KiCad by mohamedboubaker and Freq Gen MCU by joemadeus.
The 100N in open source designs
The gallery holds 7 open source boards using the 100N from 7 GitHub repositories; a typical one measures about 52 × 53 mm and carries around 46 components.
86% are two-layer designs, the rest use four layers or more, and 0% carry an open source license.
The most starred is GPS-Tracker by mohamedboubaker.
Microcontrollers on boards using the 100N
What boards using the 100N are built for
100N: common questions
Where can I find a 100N reference design?
Each of the 7 boards on this page is a real design using the 100N. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the 100N pin 1 connected?
Pin 1 is tied to 3.3V on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the 100N.
How is the 100N pin 2 connected?
Pin 2 is tied to GND on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the 100N.
What parts are used alongside the 100N?
The 10N, 10P, 10U, 30P and 4U7 appear in the most repositories here.
Which microcontrollers do boards using the 100N use?
Most are built on STM32 (6).
How big is a typical board using the 100N?
The median is 52 × 53 mm, and 86% are two-layer designs.
What is the most popular open source board using the 100N?
By GitHub stars, GPS-Tracker by mohamedboubaker, with 40 stars.
Can I simulate one of these boards using the 100N before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.