7 open source boards using the 10P
Real designs built with the 10P, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
GPS-Tracker
mohamedboubaker
35 × 53 mm53 parts2LNo license40STM32
GPS-Tracker
ibfarhat
35 × 53 mm53 parts2LNo license3STM32
Custom-STM32-PCB-With
mohamedboubaker
52 × 52 mm37 parts2LNo license2STM32
Stm32f4 sdram baseboard
ValentiWorkLearning
50 × 50 mm55 parts6LNo license1STM32
GPS-Tracker
HarshBihani18
35 × 53 mm53 parts2LNo license0STM32
Custom-STM32
dhnz-2006
52 × 52 mm37 parts2LNo license0AVR/Arduino
Usb minecraft
cnlohr
12 × 16.5 mm9 parts2LNo license472
How designs wire the 10P
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the 10P connects to, and the resistors, capacitors and other passives placed on it.
- Pin 2 is tied to GND on 7 of 7 designs.
- Pin 1 has a resistor to GND on 5 of 7 designs, most often 100 kΩ.
- Pin 1 has a series resistor on 5 of 7 designs, most often 1 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: The microcontroller 29% |
|
| Pin 2 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Usb minecraft by cnlohr, GPS-Tracker by mohamedboubaker, GPS-Tracker by ibfarhat and Custom-STM32-PCB-With-KiCad by mohamedboubaker.
The 10P in open source designs
The gallery holds 7 open source boards using the 10P from 7 GitHub repositories; a typical one measures about 35 × 52 mm and carries around 53 components.
86% are two-layer designs, the rest use four layers or more, and 0% carry an open source license.
The most starred is Usb minecraft by cnlohr.
Microcontrollers on boards using the 10P
What boards using the 10P are built for
10P: common questions
Where can I find a 10P reference design?
Each of the 7 boards on this page is a real design using the 10P. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the 10P pin 2 connected?
Pin 2 is tied to GND on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the 10P.
What resistor goes on the 10P pin 1?
Pin 1 has a resistor to GND on 5 of 7 designs, most often 100 kΩ. Counted from the KiCad layouts of 7 open source designs using the 10P.
What parts are used alongside the 10P?
The 100N, 10N, 10U, 30P and 4U7 appear in the most repositories here.
Which microcontrollers do boards using the 10P use?
Most are built on STM32 (6) and AVR/Arduino (1).
How big is a typical board using the 10P?
The median is 35 × 52 mm, and 86% are two-layer designs.
What is the most popular open source board using the 10P?
By GitHub stars, Usb minecraft by cnlohr, with 472 stars.
Can I simulate one of these boards using the 10P before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.