Electrone shelving
F9Motion·Electrone-shelving·KiCad/Electronic shelving/Electronic shelving.kicad_pcb
About the Electrone shelving PCB
Electrone shelving is an open source ESP32 PCB design by F9Motion, published on GitHub. It is a 2-layer board measuring 52.6 × 52.6 mm, with 21 components from 11 distinct parts.
Its main chip is the ESP32-C3-DevKitM-1, from the ESP32 family. Other key parts include the ER_OLEDM0.91_1x-I2C, MCP73831-2-MC and MT3608. By type, the board carries 8 diodes, 4 ICs, 4 resistors, 2 switches, 1 connector and 1 battery holder.
It belongs with the displays & leds designs in this gallery.
From the project
A electronic shelving (1.8m) to put your other projects here. This is simple shelving called electronic because the shleving have a 8 RGB Lamps in top every shelf. You can just download materials and print/solder this :)
A electronic shelving (1.8m) to put your other projects here. This is simple shelving called electronic because the shleving have a 8 RGB Lamps in top every shelf. You can just download materials and print/solder this :)
- 7 modes: Aqua, White, Yellow, Red, Purple, Blue, Green, Lime, Indigo, Soft Peach - Brightness from 10% to 100% in steps of 10% - Settings (mode and brightness) are saved and restored after power loss - Custom round PCB designed in KiCad - USB-C powered
Main components on the Electrone shelving
Electrone shelving bill of materials (BOM)
21 components, 11 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-DevKitM-1 | ESP32-C3-DevKitM-1 | U1 |
| 1 | ER_OLEDM0.91_1x-I2C | ER_OLEDM0.91_1x-I2C | U2 |
| 1 | MCP73831-2-MC | DFN-8-1EP_3x2mm_P0.5mm_EP1.7x1.4mm | U3 |
| 1 | MT3608 | SOT-23-6 | U4 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_Amphenol_124019772112A | J1 |
| 1 | Battery_Cell | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | BT1 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 2 | SW_Push | SW_SPST_PTS645Sx43SMTR92 | SW1, SW2 |
| 6 | WS2812B | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1, D2, D3, D4, D5, D6 |
| 2 | 1N4148 | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D7, D8 |
| 4 | R_Small | R_0805_2012Metric | R1, R2, R3, R4 |
Electrone shelving design files
The KiCad project lives in the F9Motion/Electrone-shelving repository on GitHub; these links point at the commit this page was built from.
Electrone shelving: common questions
What microcontroller does the Electrone shelving use?
The Electrone shelving is built around the ESP32-C3-DevKitM-1, from the ESP32 family.
How big is the Electrone shelving PCB?
The Electrone shelving measures 52.6 × 52.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Electrone shelving?
21 components, from 11 distinct parts. The full bill of materials is listed on this page.
Where can I download the Electrone shelving design files?
From the F9Motion/Electrone-shelving repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Electrone shelving design in my own project?
The repository has no license, so all rights stay with F9Motion. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Electrone shelving without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k