Esp cnc
funkBuild·esp-cnc·pcb/pcb/pcb.kicad_pcb
About the Esp cnc PCB
Esp cnc is an open source ESP32 PCB design by funkBuild, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 147.2 × 92.8 mm, with 33 components from 19 distinct parts.
Its main chip is the ESP32-WROOM, from the ESP32 family. Other key parts include the NCP1117-3.3_SOT223, 74HC595, SX1509B, TL072 and PCM5102A. By type, the board carries 12 ICs, 7 connectors, 7 resistors, 6 capacitors and 1 diode.
It belongs with the robotics & motion designs in this gallery.
From the project
A CNC controller using the ESP32
TODO - position callback called on a timer. Motion handlers register with it for each axis - Convert stepper to use position as mm instead of steps
- Brake outputs for each axis - spindle speed variation. M138 / M139 https://www.haascnc.com/service/codes-settings.type=mcode.machine=mill.value=M138.html
Haas - 4th axis - M11 unclamp, M10 clamp 5th axis - M13 unclamp, M12 clamp
Main components on the Esp cnc
Esp cnc bill of materials (BOM)
33 components, 19 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | NCP1117-3.3_SOT223 | SOT-223-3_TabPin2 | U1 |
| 1 | ESP32-WROOM | ESP32-WROOM | U2 |
| 4 | 74HC595 | SOIC-16_3.9x9.9mm_P1.27mm | U3, U4, U5, U6 |
| 1 | SX1509B | QFN-28-1EP_4x4mm_P0.4mm_EP2.4x2.4mm | U7 |
| 2 | TL072 | SOIC-8_3.9x4.9mm_P1.27mm | U8, U10 |
| 1 | PCM5102A | TSSOP-20_4.4x6.5mm_P0.65mm | U9 |
| 1 | L78L12_SOT89 | SOT-89-3 | U11 |
| 1 | L79L12_SOT89 | SOT-89-3 | U12 |
| 1 | Micro_SD_Card | R_0805_2012Metric | J1 |
| 6 | Conn_01x08_Male | PinHeader_1x08_P2.54mm_Vertical | J3, J4, J5, J6, J7, J8 |
| 1 | D | D_0805_2012Metric | D2 |
| 2 | C | C_0805_2012Metric | C1, C4 |
| 1 | 12nF | C_0805_2012Metric | C2 |
| 1 | 10uF | C_0805_2012Metric | C3 |
| 1 | 1uF/10V | C_1206_3216Metric | C5 |
| 1 | 100uF/6.3v | C_1206_3216Metric | C6 |
| 1 | 5k | R_0805_2012Metric | R1 |
| 1 | 12k | R_0805_2012Metric | R2 |
| 5 | R | R_0805_2012Metric | R3, R4, R5, R6, R7 |
Esp cnc design files
The KiCad project lives in the funkBuild/esp-cnc repository on GitHub; these links point at the commit this page was built from.
- Layoutpcb/pcb/pcb.kicad_pcb
Esp cnc: common questions
What microcontroller does the Esp cnc use?
The Esp cnc is built around the ESP32-WROOM, from the ESP32 family.
How big is the Esp cnc PCB?
The Esp cnc measures 147.2 × 92.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp cnc?
33 components, from 19 distinct parts. The full bill of materials is listed on this page.
Where can I download the Esp cnc design files?
From the funkBuild/esp-cnc repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Esp cnc design in my own project?
Yes, under the terms of its GPL-3.0 license, which funkBuild chose for the repository.
Can I test firmware for the Esp cnc without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k