Babys first

GKevinLi·babys-first-pcb

Babys first PCB layout, top view — open source ESP32 board by GKevinLi

About the Babys first PCB

Babys first is an open source ESP32 PCB design by GKevinLi, published on GitHub. It is a 2-layer board measuring 54 × 34 mm, with 35 components from 22 distinct parts.

Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the TPS82130, USBLC6-2P6, MPU-6050 and TLV76133DCY. By type, the board carries 12 capacitors, 10 resistors, 5 ICs, 3 connectors, 3 diodes and 2 switches.

It belongs with the robotics & motion, power & battery and sensors designs in this gallery.

From the project

An ESP32 devboard designed to be a drone flight controller. Includes a gyro, accelerometer, and a buck converter to step down drone battery voltage (14.8v) to 5v. Includes all the other basic devboard stuff, like an esp32, usb-c port, and io pins.

It's a custom ESP32 devboard. It was designed to be a drone flight controller, but it's suitable for other projects as well. I wanted to make this because I thought it was a good idea to try to design a drone with custom electronics. Turns out, electronics are hard, so I just made this. It'll go on the drone when all the other parts are done. This project is being made for and funded by Hack Club's Highway program.

Babys first, from the project README
From the project README

Main components on the Babys first

Babys first bill of materials (BOM)

35 components, 22 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-S3-WROOM-1
U1
1
TPS82130
U2
1
USBLC6-2P6
U3
1
MPU-6050
U4
1
TLV76133DCY
U5
1
USB_C_RECEPTACLE_USB2.0_14P
USB_C_Receptacle_USB2.0_14P
J1
2
CONN_01X16
Conn_01x16
J2, J3
2
SW_Push
SW1, SW3
1
LED
D1
2
D_Schottky
D2, D3
4
10UF
10uf
C1, C4, C6, C8
4
0U1F
0u1f
C2, C3, C5, C10
1
1UF
1uf
C7
1
3.3NF
3.3nf
C9
1
10NF
10nf
C11
1
22UF
22uf
C12
2
5K1
5k1
R1, R2
1
5.1K
5.1k
R3
2
10K
10k
R4, R5
2
100K
100k
R6, R9
Show 2 more
QtyPartRefs
2
4.7K
4.7k
R7, R8
1
523K
523k
R10

Babys first design files

The KiCad project lives in the GKevinLi/babys-first-pcb repository on GitHub; these links point at the commit this page was built from.

Babys first: common questions

What microcontroller does the Babys first use?

The Babys first is built around the ESP32-S3-WROOM-1, from the ESP32 family.

How big is the Babys first PCB?

The Babys first measures 54 × 34 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Babys first?

35 components, from 22 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Babys first design files?

From the GKevinLi/babys-first-pcb repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Babys first design in my own project?

The repository has no license, so all rights stay with GKevinLi. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Babys first without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards