Portpulse
GomGomi907·portpulse·hardware/RevC1/kicad/USB_Replug_Dongle_RevC1.kicad_pcb
About the Portpulse PCB
Portpulse is an open source WCH CH32/CH55x PCB design by GomGomi907, published on GitHub under the MIT license. It is a 4-layer board measuring 49.5 × 21.6 mm, with 29 components from 14 distinct parts.
Its main chip is the CH552T, from the WCH CH32/CH55x family. Other key parts include the CH334U, FSUSB42MUX, TPS2552DBVR, XC6206P332MR-G and USBLC6-2SC6. By type, the board carries 10 capacitors, 9 resistors, 7 ICs, 2 connectors and 1 crystal.
From the project
PortPulse는 PC와 USB 장치(DUT) 사이에 연결하는 USB 2.0 재연결 동글입니다.
PortPulse는 PC와 USB 장치(DUT) 사이에 연결하는 USB 2.0 재연결 동글입니다.
PC와 제어 MCU의 연결은 유지한 채, 외부 DUT의 VBUS와 D+/D−를 소프트웨어로 차단하고 복구합니다. 따라서 USB 장치를 실제로 뽑았다가 다시 연결하는 동작을 자동화 테스트에서 재현할 수 있습니다.
1. PortPulse의 USB-C upstream 포트를 PC에 연결합니다. 2. DUT를 PortPulse의 USB-A downstream 포트에 연결합니다. 3. 장치 관리자에서 PortPulse의 COM 포트 번호를 확인합니다. 4. 네이티브 portpulse 프로그램으로 명령을 보냅니다.
- on: DUT 연결 - off: DUT 차단 - cycle: DUT를 차단한 뒤 지정한 시간 후 다시 연결 - status: 현재 상태 확인 - fault: 전원 스위치 Fault 상태 확인 - version: 펌웨어 버전 확인
Main components on the Portpulse
Portpulse bill of materials (BOM)
29 components, 14 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CH334U WCH | QSOP-28_3.9x9.9mm_P0.635mm | U1 |
| 1 | CH552T WCH | TSSOP-20_4.4x6.5mm_P0.65mm | U2 |
| 1 | FSUSB42MUX onsemi | MSOP-10_3x3mm_P0.5mm | U3 |
| 1 | TPS2552DBVR Texas Instruments | SOT-23-6 | U4 |
| 1 | XC6206P332MR-G Torex | SOT-23 | U5 |
| 2 | USBLC6-2SC6 STMicroelectronics | SOT-23-6 | U6, U7 |
| 1 | X322512MSB4SI 12 MHz YXC | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | TYPE-C-3.1-16PIN SHOU HAN | C7507405_USB_C | J1 |
| 1 | 904-131A2032S10100 Jing Extension of the Electronic Co. | C8328_USB_A | J2 |
| 2 | 10uF 10V X5R Generic | C_0603_1608Metric | C1, C10 |
| 2 | 1uF 16V X5R Generic | C_0603_1608Metric | C2, C3 |
| 6 | 100nF 16V X7R Generic | C_0603_1608Metric | C4, C5, C6, C7, C8, C9 |
| 8 | 5.1k 1% Generic | R_0603_1608Metric | R1, R2, R4, R5, R6, R7, R8, R9 |
| 1 | 51k 1% Generic | R_0603_1608Metric | R10 |
Portpulse design files
The KiCad project lives in the GomGomi907/portpulse repository on GitHub; these links point at the commit this page was built from.
Portpulse: common questions
What microcontroller does the Portpulse use?
The Portpulse is built around the CH552T, from the WCH CH32/CH55x family.
How big is the Portpulse PCB?
The Portpulse measures 49.5 × 21.6 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Portpulse?
29 components, from 14 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Portpulse design files?
From the GomGomi907/portpulse repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Portpulse design in my own project?
Yes, under the terms of its MIT license, which GomGomi907 chose for the repository.
Can I test firmware for the Portpulse without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug WCH CH32/CH55x firmware against it before you order a PCB.
Similar boards
WCH CH32/CH55x
Ps2usb
rasteri
40 × 55 mm25 parts2LNo license428WCH CH32/CH55x
CH32X-48
rgoulter
224.6 × 74.2 mm112 parts2LNo license230WCH CH32/CH55x
CH32X-60-ANSI-Improved
rgoulter
285 × 94.2 mm149 parts2LNo license230WCH CH32/CH55x
CH32X-75
rgoulter
285 × 94.2 mm318 parts2LNo license230WCH CH32/CH55x
CH552-48
rgoulter
224.6 × 74.2 mm107 parts2LNo license230WCH CH32/CH55x
Webusb programmer rev6
laneboysrc
38 × 20 mm18 parts2LMIT87