54 open source boards using the FSUSB42MUX
Real designs built with the FSUSB42MUX, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Raspberry Pi
Wall Panel
dotstartech
75 × 79 mm99 parts8LCERN-OHL-W-2.0366RP2040/RP2350
Vaio re
CRImier
75 × 65 mm274 parts4LGPL-3.0254AVR/Arduino
Gamma split
ahtn
109 × 71 mm120 parts2LNo license96Raspberry Pi
Pi CM4 16
computergeek1507
142.1 × 106 mm113 parts2LCERN-OHL-S-2.078RP2040/RP2350
Lemon pcb swizzle
rianadon
31.9 × 36 mm56 parts2LNo license41STM32
Ferret
fullyautomated
50 × 50 mm116 parts4LNo license20FPGA
Fast open switch r1.0
PCB-Arts
230 × 225 mm909 parts12LNo license14RP2040/RP2350
Pedalboard hw
pedalboard
174 × 111 mm142 parts2LCERN-OHL-P-2.014Raspberry Pi
CM4IOv5-clone
sergiomd4
160 × 90 mm137 parts4LCC0-1.010Raspberry Pi
Unifying
balthazar-space
120.9 × 78.8 mm121 parts4LCERN-OHL-S-2.07STM32
Twinusb
s-t-e-f-a-n
63 × 20 mm112 parts4LNo license7RP2040/RP2350
Board
wang-edward
300 × 120 mm228 parts4LMIT5ESP32
Raven1106
EPSILON0-dev
86 × 56 mm209 parts4LNo license4Raspberry Pi
Matarael
h3430
160 × 90 mm137 parts4LNo license3STM32
CM4IOv5
DevCyclonekitten
160 × 90 mm137 parts4LGPL-3.02Raspberry Pi
Bugg main r5
bugg-resources
57.3 × 109 mm377 parts6LCC-BY-NC-4.01Raspberry Pi
Cm5
YORROY123
170 × 120 mm221 parts4LMIT1ESP32
Dji fcc esp32
nikolaus018
80 × 34 mm56 parts2LMIT1Skibidi usb mux
tobycm
75 × 35 mm29 parts2LMIT1Dev board1
tbennellick
250 × 167.9 mm775 parts6LNo license0Raspberry Pi
Hexa-Pi
rickcox
150 × 150 mm352 parts4LCC-BY-4.00STM32
Dual Axis Controller
jrseti
140 × 100 mm307 parts4LCC0-1.00STM32
RCM DishControllerBoard
jrseti
140 × 100 mm304 parts4LMIT0STM32
XYmatics-E64
XyrusB2010
191.3 × 97.8 mm277 parts2LNo license0ESP32
Felső panel
NBence0
120.1 × 70.2 mm274 parts6LNo license0RP2040/RP2350
Nref motherboard
cetola
122.6 × 75.9 mm269 parts6LNo license0Raspberry Pi
CrallyBoard
cruunnerr
180.7 × 143.8 mm226 parts2LNo license0RP2040/RP2350
UMMTJ Mainboard
vamatis
100 × 100 mm142 parts4LNo license0Raspberry Pi
CM4IOv5
JRavenelco
160 × 90 mm137 parts4LNo license0ESP32
Controller
micthiesen
150 × 110 mm99 parts4LNo license0Raspberry Pi
Esp
jayadeep14
86.5 × 64.8 mm91 parts2LNo license0ESP32
Bay node
kartben
64 × 80 mm74 parts4LApache-2.00Raspberry Pi
Raspberry Pi CM4 Carrier for SPIKE Prime
EricYufengWu
52.3 × 84.3 mm57 parts4LNo license0Raspberry Pi
Roboclaw cm4-dc dish controller
jrseti
145.8 × 76.9 mm49 parts2LMIT0WCH CH32/CH55x
Portpulse
GomGomi907
49.5 × 21.6 mm29 parts4LMIT0WCH CH32/CH55x
Portpulse
gslee-dev
49.5 × 21.6 mm29 parts4LMIT0
How designs wire the FSUSB42MUX
Read from the KiCad layouts of 43 open source designs, one per repository: what each pin of the FSUSB42MUX connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 30 of 43 designs, most often 100 nF (then 10 µF).
- The SEL pin has a resistor to GND on 25 of 43 designs, most often 2.2 kΩ (then 10 kΩ).
- The NOE pin is tied to GND on 29 of 41 designs (not connected on 2, a signal on 10).
- The SEL pin has a series resistor on 23 of 43 designs, most often 2.2 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCCpin 1 | Connected to: 3.3V 81% · a signal 16% |
|
| SELpin 2 | Connected to: Signal 84% |
|
| GNDpin 5 | Connected to: GND 98% | — |
| NOEpin 10 | Connected to: GND 71% · a signal 24% | — |
6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Wall Panel by dotstartech, Vaio re by CRImier, Gamma split by ahtn and BladeCore-M54E by DvidMakesThings.
The FSUSB42MUX in open source designs
The gallery holds 54 open source boards using the FSUSB42MUX from 44 GitHub repositories; a typical one measures about 120.9 × 86.1 mm and carries around 137 components.
72% use four copper layers or more, and 43% carry an open source license.
The most starred is Wall Panel by dotstartech.
Parts used alongside the FSUSB42MUX
Microcontrollers on boards using the FSUSB42MUX
What boards using the FSUSB42MUX are built for
FSUSB42MUX: common questions
Where can I find a FSUSB42MUX reference design?
Each of the 54 boards on this page is a real design using the FSUSB42MUX. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the FSUSB42MUX VCC pin?
The VCC pin has a decoupling capacitor on 30 of 43 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 43 open source designs using the FSUSB42MUX.
What resistor goes on the FSUSB42MUX SEL pin?
The SEL pin has a resistor to GND on 25 of 43 designs, most often 2.2 kΩ (then 10 kΩ). Counted from the KiCad layouts of 43 open source designs using the FSUSB42MUX.
How is the FSUSB42MUX NOE pin connected?
The NOE pin is tied to GND on 29 of 41 designs (not connected on 2, a signal on 10). Counted from the KiCad layouts of 43 open source designs using the FSUSB42MUX.
What parts are used alongside the FSUSB42MUX?
The TPD4EUSB30, USB2514B-I/M2, 74LVC1G07SE-7, AP64501SP-13 and AP22653W6 appear in the most repositories here.
Which microcontrollers do boards using the FSUSB42MUX use?
Most are built on Raspberry Pi (21), RP2040/RP2350 (7), STM32 (6) and ESP32 (6).
How big is a typical board using the FSUSB42MUX?
The median is 120.9 × 86.1 mm, and 28% are two-layer designs.
What is the most popular open source board using the FSUSB42MUX?
By GitHub stars, Wall Panel by dotstartech, with 366 stars.
Can I simulate one of these boards using the FSUSB42MUX before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.