6 open source boards using the TPS2552DBVR
Real designs built with the TPS2552DBVR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Relaymux
PetteriAimonen
120.4 × 100.4 mm55 parts2LBSD-2-Clause18Optimus-Hub
devisunofficial
72.7 × 88.7 mm76 parts4LNo license0Usb replug
clankagent
70 × 30 mm39 parts4LNo license0WCH CH32/CH55x
Portpulse
GomGomi907
49.5 × 21.6 mm29 parts4LMIT0WCH CH32/CH55x
Portpulse
gslee-dev
49.5 × 21.6 mm29 parts4LMIT0USB-A-Daughterboard
nearestexit
96.1 × 29.3 mm52 parts2LMIT40
How designs wire the TPS2552DBVR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TPS2552DBVR connects to, and the resistors, capacitors and other passives placed on it.
- The ILIM pin has a resistor to GND on 5 of 6 designs, most often 51 kΩ (then 68 kΩ).
- The EN pin has a pull-up to VBUS_IN on 4 of 6 designs, most often 5.1 kΩ (then 10 kΩ).
- The VIN pin has a decoupling capacitor on 3 of 6 designs, most often 100 nF (then 10 µF).
- The FAULT pin has a pull-up to VBUS_IN on 3 of 6 designs, most often 5.1 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VINpin 1 | Connected to: VBUS_IN 83% · a signal 17% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| ENpin 3 | Connected to: The microcontroller 50% |
|
| FAULTpin 4 | Connected to: The microcontroller 33% · not connected 17% |
|
| ILIMpin 5 | Connected to: Signal 100% |
|
| VOUTpin 6 | Connected to: 5V 83% · a signal 17% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include USB-A-Daughterboard by nearestexit, Relaymux by PetteriAimonen, Usb replug by clankagent and Optimus-Hub by devisunofficial.
The TPS2552DBVR in open source designs
The gallery holds 6 open source boards using the TPS2552DBVR from 6 GitHub repositories; a typical one measures about 71.3 × 29.6 mm and carries around 46 components.
67% use four copper layers or more, and 67% carry an open source license.
The most starred is USB-A-Daughterboard by nearestexit.
Parts used alongside the TPS2552DBVR
Microcontrollers on boards using the TPS2552DBVR
What boards using the TPS2552DBVR are built for
TPS2552DBVR: common questions
Where can I find a TPS2552DBVR reference design?
Each of the 6 boards on this page is a real design using the TPS2552DBVR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TPS2552DBVR ILIM pin?
The ILIM pin has a resistor to GND on 5 of 6 designs, most often 51 kΩ (then 68 kΩ). Counted from the KiCad layouts of 6 open source designs using the TPS2552DBVR.
What pull-up resistor is used on the TPS2552DBVR EN pin?
The EN pin has a pull-up to VBUS_IN on 4 of 6 designs, most often 5.1 kΩ (then 10 kΩ). Counted from the KiCad layouts of 6 open source designs using the TPS2552DBVR.
What decoupling capacitors do designs use on the TPS2552DBVR VIN pin?
The VIN pin has a decoupling capacitor on 3 of 6 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 6 open source designs using the TPS2552DBVR.
What parts are used alongside the TPS2552DBVR?
The CH334U, CH552T, FSUSB42MUX, USBLC6-2SC6 and XC6206P332MR-G appear in the most repositories here.
Which microcontrollers do boards using the TPS2552DBVR use?
Most are built on WCH CH32/CH55x (2) and STM32 (1).
How big is a typical board using the TPS2552DBVR?
The median is 71.3 × 29.6 mm, and 33% are two-layer designs.
What is the most popular open source board using the TPS2552DBVR?
By GitHub stars, USB-A-Daughterboard by nearestexit, with 40 stars.
Can I simulate one of these boards using the TPS2552DBVR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.