Pcb esp32s3-epaper

haiha-ux·pcb-esp32s3-epaper

Pcb esp32s3-epaper layout, top view — open source ESP32 board by haiha-ux

About the Pcb esp32s3-epaper

Pcb esp32s3-epaper is an open source ESP32 PCB design by haiha-ux, published on GitHub. It is a 4-layer board measuring 72 × 48 mm, with 53 components from 34 distinct parts.

Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the USBLC6-2SC6, MCP73831T-2ACI/OT and RT9080-33GJ5. By type, the board carries 19 capacitors, 15 resistors, 6 diodes, 4 ICs, 4 connectors and 2 transistors.

It belongs with the power & battery, displays & leds and iot & wireless designs in this gallery.

From the project

ESP32-S3 4-layer board in KiCad 10: USB-C, LiPo charger with load sharing, 24-pin e-paper boost, JLCPCB-ready fab files

A 72 × 48 mm battery board that drives a bare SPI e-paper panel from an ESP32-S3-WROOM-1 module. The module's PCB antenna sits at the board edge. USB-C goes straight to the S3's native USB, so there is no UART bridge. A single-cell LiPo charger with load sharing feeds a 3.3 V LDO that draws 2 µA quiescent. A 24-pin FPC takes Good Display style panels, with the panel's boost and charge pump on board. The board also has a Qwiic/STEMMA QT port, a status LED, BOOT and RESET buttons, and four M3 holes.

Pcb esp32s3-epaper, from the project README
From the project README

Main components on the Pcb esp32s3-epaper

Pcb esp32s3-epaper bill of materials (BOM)

53 components, 34 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
USBLC6-2SC6
U1
1
MCP73831T-2ACI/OT
MCP73831-2-OT
U2
1
RT9080-33GJ5
U3
1
ESP32-S3-WROOM-1-N16R8
U4
1
AO3401A
Q1
1
SI1308EDL-T1-GE3
Si1308EDL
Q2
1
TYPE-C-31-M-12
USB-C
J1
1
S2B-PH-SM4-TB(LF)(SN)
LiPo 1S
J2
1
SM04B-SRSS-TB(LF)(SN)
Qwiic I2C
J3
1
AFC07-S24FCA-00
EPD FPC 24P 0.5mm
J4
1
TS-1187A-B-A-B
RESET
SW1
1
TS-1187A-B-A-B
BOOT
SW2
1
B5819W SL
B5819W
D1
1
KT-0603R
RED CHG
D2
1
KT-0603R
RED STAT
D3
3
MBR0530T1G
MBR0530
D4, D5, D6
1
PNR3015-470M
47uH 580mA
L1
3
CL21A475KAQNNNE
4.7uF 25V
C1, C9, C11
2
CL21A106KAYNNNE
10uF 25V
C2, C3
1
CL10A106KP8NNNC
10uF
C4
Show 14 more
QtyPartRefs
2
CL05B104KO5NNNC
100nF
C5, C7
1
CL21A226MAQNNNE
22uF 25V
C6
1
CL05A105KA5NQNC
1uF
C8
1
1206B475K500NT
4.7uF 50V X7R
C10
8
CL10A105KB8NNNC
1uF 50V
C12, C13, C14, C15, C16, C17, C18, C19
2
0402WGF5101TCE
5.1k
R1, R2
1
0402WGF3301TCE
3.3k
R3
2
0402WGF1001TCE
1k
R4, R9
1
0402WGF1003TCE
100k
R5
3
0402WGF1004TCE
1M
R6, R7, R12
1
0402WGF1002TCE
10k
R8
2
0402WGF4701TCE
4.7k
R10, R11
1
0603WAF220KT5E
2.2R
R13
2
0402WGF220JTCE
22R
R14, R15

Pcb esp32s3-epaper design files

The KiCad project lives in the haiha-ux/pcb-esp32s3-epaper repository on GitHub; these links point at the commit this page was built from.

Pcb esp32s3-epaper: common questions

What microcontroller does the Pcb esp32s3-epaper use?

The Pcb esp32s3-epaper is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.

How big is the Pcb esp32s3-epaper?

The Pcb esp32s3-epaper measures 72 × 48 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Pcb esp32s3-epaper?

53 components, from 34 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Pcb esp32s3-epaper design files?

From the haiha-ux/pcb-esp32s3-epaper repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Pcb esp32s3-epaper design in my own project?

The repository has no license, so all rights stay with haiha-ux. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Pcb esp32s3-epaper without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards