Płytka główna
KamilWuu·Line_Follower_ZACZ·electronics/Płytka główna/Płytka główna.kicad_pcb
About the Płytka główna PCB
Płytka główna is an open source ESP32 PCB design by KamilWuu, published on GitHub. It is a 2-layer board measuring 99.8 × 74.5 mm, with 64 components from 29 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N8R8, from the ESP32 family. Other key parts include the TPS563201DDCR, BMI270 and TB6612FNG. By type, the board carries 23 capacitors, 18 resistors, 9 connectors, 5 ICs, 1 switch and 1 LED.
It belongs with the robotics & motion designs in this gallery.
From the project
line follower robot
Main components on the Płytka główna
Płytka główna bill of materials (BOM)
64 components, 29 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TPS563201DDCR | SOT95P280X110-6N | IC1 |
| 1 | BMI270 | QFN50P300X250X87-14N | IC2 |
| 1 | ESP32-S3-WROOM-1-N8R8 | ESP32-S3-WROOM-1 | U1 |
| 2 | TB6612FNG | SSOP-24_5.3x8.2mm_P0.65mm | U2, U3 |
| 1 | Conn_01x26_Socket | Molex_200528-0260_1x26-1MP_P1.00mm_Horizontal | J2 |
| 2 | Conn_01x06_Socket | PinHeader_1x06_P2.00mm_Vertical | J3, J4 |
| 1 | battery_connector | PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | Conn_01x03_Pin | PinHeader_1x03_P2.54mm_Vertical | J6 |
| 1 | batt_switch | PinHeader_1x03_P2.54mm_Vertical | J7 |
| 3 | Conn_01x05_Pin | PinHeader_1x05_P2.00mm_Vertical | J8, J9, J10 |
| 4 | SolderJumper_3_Open | SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm | AIN1, AIN2, BIN1, BIN2 |
| 1 | SW_Push_Dual_x2 | SW_Push_1P1T_XKB_TS-1187A | BOOT0 |
| 1 | MPU-6050 | InvenSense_QFN-24_4x4mm_P0.5mm | MPU-6050 |
| 1 | SW_Push_Dual_x2 | SW_PUSH_6mm_H7.3mm | SW4 |
| 1 | LED | LED_0603_1608Metric | 3.3V |
| 1 | 2.2uH | L_Bourns_SRP7028A_7.3x6.6mm | L1 |
| 12 | 0.1uF | C_0603_1608Metric | C1, C6, C7, C9, C10, C11, C12, C14 +4 |
| 3 | 22uF | C_0805_2012Metric | C2, C3, C8 |
| 2 | 10uF | C_0805_2012Metric | C4, C5 |
| 2 | >10uF/3.3V | CP_EIA-3528-21_Kemet-B | C13, C17 |
Show 9 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | >10uF/8.4V | CP_EIA-3528-21_Kemet-B | C15, C19 |
| 1 | 2.2nF | C_0603_1608Metric | C20 |
| 1 | 10nF | C_0603_1608Metric | C23 |
| 2 | 10kR | R_0603_1608Metric | R1, R3 |
| 1 | 33.2kR | R_0603_1608Metric | R2 |
| 9 | 10K | R_0603_1608Metric | R4, R5, R6, R7, R8, R13, R14, R15 +1 |
| 2 | ? | R_0603_1608Metric | R9, R12 |
| 1 | 220 | R_0603_1608Metric | R10 |
| 3 | 2K | R_0603_1608Metric | R11, R17, R18 |
Płytka główna design files
The KiCad project lives in the KamilWuu/Line_Follower_ZACZ repository on GitHub; these links point at the commit this page was built from.
Płytka główna: common questions
What microcontroller does the Płytka główna use?
The Płytka główna is built around the ESP32-S3-WROOM-1-N8R8, from the ESP32 family.
How big is the Płytka główna PCB?
The Płytka główna measures 99.8 × 74.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Płytka główna?
64 components, from 29 distinct parts. The full bill of materials is listed on this page.
Where can I download the Płytka główna design files?
From the KamilWuu/Line_Follower_ZACZ repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Płytka główna design in my own project?
The repository has no license, so all rights stay with KamilWuu. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Płytka główna without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Line_Follower_ZACZ
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k