LF 1
KamilWuu·Line_Follower_ZACZ·electronics/LF_1.kicad_pcb
About the LF 1 PCB
LF 1 is an open source ESP32 PCB design by KamilWuu, published on GitHub. It is a 2-layer board, with 77 components from 26 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N8R8, from the ESP32 family. Other key parts include the TPS563201DDCR, BMI270, ITR8307-S17-TR8 and LM2901. By type, the board carries 36 resistors, 14 ICs, 13 capacitors, 3 connectors, 2 LEDs and 1 inductor.
It belongs with the robotics & motion designs in this gallery.
From the project
line follower robot
Main components on the LF 1
LF 1 bill of materials (BOM)
77 components, 26 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TPS563201DDCR | SOT95P280X110-6N | IC1 |
| 1 | BMI270 | QFN50P300X250X87-14N | IC2 |
| 2 | ESP32-S3-WROOM-1-N8R8 | XCVR_ESP32S3WROOM1N8R8 | U1, U2 |
| 8 | ITR8307-S17-TR8 | Everlight_ITR1201SR10AR | U3, U4, U5, U6, U9, U10, U11, U12 |
| 2 | LM2901 | U7, U8 | |
| 1 | Conn_01x04_Male | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 2 | Conn_01x24_Socket | J2, J3 | |
| 4 | SolderJumper_3_Open | SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm | AIN1, AIN2, BIN1, BIN2 |
| 3 | SW_MEC_5G | EN1, IO1, IO2 | |
| 1 | R_Potentiometer | RV1 | |
| 2 | LED | LED_0603_1608Metric | 3.3V1, VBAT1 |
| 1 | 2.2uH | L1 | |
| 2 | 0.1uF | C1, C6 | |
| 2 | 22uF | C2, C3 | |
| 2 | 10uF | C4, C5 | |
| 5 | 0.1uF | C_0603_1608Metric | C7, C8, C10, C12, C13 |
| 1 | >10uF/3.3V | CP_EIA-3528-21_Kemet-B | C9 |
| 1 | >10uF/8.4V | CP_EIA-3528-21_Kemet-B | C11 |
| 2 | 10kR | R1, R3 | |
| 1 | 33.2kR | R2 |
Show 6 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 7 | 10K | R_0603_1608Metric | R4, R5, R6, R7, R10, R23, R24 |
| 1 | 220 | R_0603_1608Metric | R8 |
| 1 | 1K | R_0603_1608Metric | R9 |
| 8 | 22kR | R11, R13, R15, R17, R26, R28, R32, R34 | |
| 8 | 110R | R12, R14, R16, R18, R27, R29, R33, R36 | |
| 8 | 15kR | R19, R20, R21, R22, R25, R30, R31, R35 |
LF 1 design files
The KiCad project lives in the KamilWuu/Line_Follower_ZACZ repository on GitHub; these links point at the commit this page was built from.
- Layoutelectronics/LF_1.kicad_pcb
- Schematicelectronics/LF_1.kicad_sch
LF 1: common questions
What microcontroller does the LF 1 use?
The LF 1 is built around the ESP32-S3-WROOM-1-N8R8, from the ESP32 family.
How big is the LF 1 PCB?
The LF 1 has 2 copper layers and is 1.6 mm thick.
How many components are on the LF 1?
77 components, from 26 distinct parts. The full bill of materials is listed on this page.
Where can I download the LF 1 design files?
From the KamilWuu/Line_Follower_ZACZ repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the LF 1 design in my own project?
The repository has no license, so all rights stay with KamilWuu. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the LF 1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Line_Follower_ZACZ
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k