ParkFlow

kgchord·ParkFlow·electronics/kicad/lane_controller.kicad_pcb

ParkFlow PCB layout, top view — open source ESP32 board by kgchord

About the ParkFlow PCB

ParkFlow is an open source ESP32 PCB design by kgchord, published on GitHub. It is a 2-layer board measuring 100 × 80 mm, with 145 components from 80 distinct parts.

Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the TPS54560BDDA, TLV62569DBVR, USBLC6-2SC6, TPS3823-33DBVR (WDT 1.6 s) and THVD1450DR. By type, the board carries 60 resistors, 27 capacitors, 17 ICs, 17 diodes, 12 connectors and 5 transistors.

From the project

FASTag (UHF RFID) + ANPR fusion on an on-site Edge Node for stop-free, token-free parking in India. Vishwakarma Awards 2026-27, Stage 2 engineering package (prototype: the "ParkFlow Demo Lane").

FASTag (UHF RFID) + ANPR fusion on an on-site Edge Node for stop-free, token-free parking in India. Vishwakarma Awards 2026-27, Stage 2 engineering package (prototype: the "ParkFlow Demo Lane").

Status (25 Oct 2026): design stage. No hardware has been built or bench-tested yet. Performance figures are targets or predictions to be bench-verified, unless a log in the repo shows a measured run. Billing goes to a mock NETC ledger; no real FASTag debit is attempted.

Main components on the ParkFlow

TPS54560BDDATLV62569DBVRUSBLC6-2SC6ESP32-S3-WROOM-1-N16R8TPS3823-33DBVR (WDT 1.6 s)THVD1450DR74AHCT1G08 (LPWM = CLOSE only if BEAM_CLEAR)EL817S1(C) / PC817SN74HCT245PWR (5 V, TTL inputs)74AHCT1G08 (RPWM = OPEN request & ESTOP_OK)

ParkFlow bill of materials (BOM)

145 components, 80 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
TPS54560BDDA
U1
1
TLV62569DBVR
U2
1
USBLC6-2SC6
U3
1
ESP32-S3-WROOM-1-N16R8
U4
1
TPS3823-33DBVR (WDT 1.6 s)
U5
1
THVD1450DR
U6
1
74AHCT1G08 (R_EN = L_EN = MOT_EN & ESTOP_OK, 5 V out)
U9
1
74AHCT1G08 (LPWM = CLOSE only if BEAM_CLEAR)
U10
7
EL817S1(C) / PC817
U11, U12, U13, U14, U15, U16, U17
1
SN74HCT245PWR (5 V, TTL inputs)
U18
1
74AHCT1G08 (RPWM = OPEN request & ESTOP_OK)
U19
1
FQD11P06 (-60V P-FET)*
Q1
2
2N7002
Q2, Q3
1
IRLML0060TRPBF (60V)
Q4
1
IRLML0060TRPBF
Q5
1
24V_LOGIC_IN
J1
1
E-STOP NC LOOP + K1 COIL
J4
1
FIELD I/O 8P
J5
1
PSU/UPS STATUS (AC-OK, BAT-OK dry contacts to +24V)
J6
1
RS485 RFID (A,B,0V)
J7
Show 60 more
QtyPartRefs
1
BUZZER 24V (+, -)
J8
1
HUB12 2x8 IDC (verify vs P10 silkscreen)
J9
1
WS2812 JST-XH 3P (B3B-XH-A)
J10
1
EDGE LINK JST-XH 5P (B5B-XH-A)
J11
1
USB-C 16P (GCT USB4105-GF-A)
J12
1
P10 SIGN POWER 5V/3A
J13
1
IBT-2 LOGIC 1x8 (RPWM,LPWM,R_EN,L_EN,R_IS,L_IS,VCC,GND)
J14
1
3A NANO2 0451003.MRL (very fast-acting)
F1
1
MF-R075 (0.75A hold, 60V)
F2
1
TERM EN
JP1
1
BOOT
SW1
1
RESET
SW2
1
BZT52C15 (Vgs clamp)
D1
1
SMBJ33A
D2
1
B560C (60V 5A)
D3
1
SS14 (VBUS OR)
D4
1
BAT54W
D5
1
GREEN 0603 (3V3 OK)
D6
1
SM712
D7
1
BAT54S (ADC clamp)
D9
6
1N4148W (rev.)
D10, D11, D12, D13, D14, D15
1
S1M (coil flyback)
D16
1
1N4148W
D17
1
SS14 (5V OR)
D18
1
6.8uH Isat>=7A*
L1
1
2.2uH 3A
L2
1
100uF 50V
C1
7
100nF
C2, C6, C13, C15, C19, C20, C22
2
4.7uF 50V X7R
C3, C4
1
6.8nF* (Cc)
C5
2
47uF 10V X5R
C7, C8
1
10uF 10V
C9
2
22uF 10V
C10, C11
1
22uF
C12
1
1uF
C14
8
10nF
C18, C30, C31, C32, C33, C34, C35, C36
1
470uF 10V (LED bulk)
C21
12
10k
R1, R3, R8, R15, R16, R41, R45, R49 +4
9
100k
R2, R10, R19, R20, R30, R31, R32, R78 +1
1
200k (fsw 500 kHz)
R4
1
10k* (Rc)
R5
1
100k (EN/UVLO upper)
R6
1
53.6k (Vout=5.09V)
R7
1
453k
R9
2
5.1k
R11, R12
2
22R
R13, R14
4
100R
R17, R18, R77, R80
2
1k
R21, R29
1
10k (DE pull-down)
R22
2
680R fail-safe bias (DNP)
R23, R24
1
120R term
R25
1
1k* R_IS (DNP: the IBT-2 module already has 1k on each IS pin)
R28
7
4.7k 1206
R40, R44, R48, R52, R56, R60, R82
1
10k (OE pull-up: sign off at reset)
R64
6
33R
R70, R71, R72, R73, R74, R75
1
330R
R76
1
10k (EN/UVLO lower, UVLO ~13 V)
R90
1
100R (IS_A isolation)
R91
1
100R (IS_B isolation)
R92
1
10k (unused A7 tie)
R93

ParkFlow design files

The KiCad project lives in the kgchord/ParkFlow repository on GitHub; these links point at the commit this page was built from.

ParkFlow: common questions

What microcontroller does the ParkFlow use?

The ParkFlow is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.

How big is the ParkFlow PCB?

The ParkFlow measures 100 × 80 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the ParkFlow?

145 components, from 80 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the ParkFlow design files?

From the kgchord/ParkFlow repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the ParkFlow design in my own project?

The repository has no license, so all rights stay with kgchord. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the ParkFlow without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards