Booth
Lavapeeble·elec3117·booth_pcb/booth_pcb.kicad_pcb
About the Booth PCB
Booth is an open source ESP32 PCB design by Lavapeeble, published on GitHub. It is a 4-layer board measuring 76.8 × 43.7 mm, with 50 components from 20 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the SUL6001S5-33, TS3USB30EDGSR and 24LC00. By type, the board carries 16 resistors, 14 capacitors, 7 connectors, 6 ICs and 2 diodes.
Main components on the Booth
Booth bill of materials (BOM)
50 components, 20 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | SUL6001S5-33 | SOT-23-5 | U2 |
| 1 | TS3USB30EDGSR | Texas_UQFN-10_1.5x2mm_P0.5mm | U3 |
| 3 | 24LC00 | SOP-8_3.76x4.96mm_P1.27mm | U4, U5, U6 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01A | J1 |
| 1 | USB_A | USB_A_Receptacle_GCT_USB1046 | J2 |
| 1 | JTAG | PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | Conn_01x02_Pin | PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | Conn_01x10_Pin | PinHeader_1x10_P2.54mm_Vertical | J5 |
| 2 | Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | J6, J7 |
| 5 | SW_Push | SW_SPST_TS-1088-xR025 | CONFIRM1, DOWN1, UNDO1, UP1, VOTE1 |
| 1 | GRN | LED_D4.0mm | D1 |
| 1 | RED | LED_D4.0mm | D2 |
| 5 | 1u | C_0603_1608Metric | C1, C2, C4, C13, C14 |
| 9 | 100n | C_0402_1005Metric | C5, C6, C7, C8, C9, C10, C11, C12 +1 |
| 6 | 10k | R_0402_1005Metric | R1, R2, R3, R4, R5, R6 |
| 6 | 5.1k | R_0402_1005Metric | R9, R10, R11, R12, R13, R14 |
| 1 | 1.5k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R15 |
| 1 | 150 | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R16 |
| 2 | 22R | R_0402_1005Metric | R17, R18 |
Booth design files
The KiCad project lives in the Lavapeeble/elec3117 repository on GitHub; these links point at the commit this page was built from.
- Layoutbooth_pcb/booth_pcb.kicad_pcb
- Schematicbooth_pcb/booth_pcb.kicad_sch
Booth: common questions
What microcontroller does the Booth use?
The Booth is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the Booth PCB?
The Booth measures 76.8 × 43.7 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Booth?
50 components, from 20 distinct parts. The full bill of materials is listed on this page.
Where can I download the Booth design files?
From the Lavapeeble/elec3117 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Booth design in my own project?
The repository has no license, so all rights stay with Lavapeeble. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Booth without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in elec3117
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k