20 open source boards using the TS3USB30EDGSR
Real designs built with the TS3USB30EDGSR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Microchip SAM
Kira
kiibohd
366.9 × 114.3 mm400 partsCERN-OHL-1.2416Raspberry Pi
Scalenode cm4-baseboard
antmicro
128.5 × 40 mm125 parts4LApache-2.0151STM32
Hub
Bruhdows
148 × 78 mm309 parts4LNo license1STM32
Atlas drive
AtlasAutoware
140 × 90 mm377 parts6LNo license0RP2040/RP2350
Nref motherboard
cetola
122.6 × 75.9 mm269 parts6LNo license0Raspberry Pi
ROV PCIE USB HUB FINAL
samnadol
65 × 56.5 mm161 parts4LNo license0RP2040/RP2350
FarmMesh-Node
chinawrj
100 × 100 mm153 parts4LNo license0Mgc
0x007E
92.7 × 62.2 mm108 parts2LCC-BY-NC-4.00ESP32
Booth
Lavapeeble
76.8 × 43.7 mm50 parts4LNo license0Usb replug
clankagent
70 × 30 mm39 parts4LNo license0NXP
K-Type
kiibohd
357.5 × 131.8 mm361 partsCERN-OHL-1.2416Sd mux
3mdeb
50 × 114 mm48 parts2LApache-2.08Sd mux
emaste
50 × 114 mm48 parts2LApache-2.02Sd mux
3mdeb
50 × 114 mm48 parts2LApache-2.01Rov usb
samnadol
55.5 × 68.5 mm133 parts4LNo license0Sd mux
moto-timo
50 × 114 mm48 parts2LApache-2.00Sd mux
agners
50 × 114 mm48 parts2LApache-2.00Sd mux
capotosto
50 × 114 mm48 parts2LApache-2.00NXP
Testcontroller
kiibohd
145.8 × 42.9 mm45 parts2LCERN-OHL-1.241600001-008
marian-scientific
59 × 66 mm9 parts2LNo license0
How designs wire the TS3USB30EDGSR
Read from the KiCad layouts of 17 open source designs, one per repository: what each pin of the TS3USB30EDGSR connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 8 of 16 designs, most often 100 nF (then 10 µF).
- The S pin has a pull-up to VDD on 7 of 17 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Spin 1 | Connected to: 74AHC1G14 35%, FT245RL 35% · GND 18% |
|
| GNDpin 5 | Connected to: GND 94% | — |
| VCCpin 10 | Connected to: VDD 75% · a signal 25% |
|
7 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include K-Type by kiibohd, Scalenode cm4-baseboard by antmicro, Sd mux by 3mdeb and Sd mux by emaste.
The TS3USB30EDGSR in open source designs
The gallery holds 20 open source boards using the TS3USB30EDGSR from 17 GitHub repositories; a typical one measures about 73.4 × 84 mm and carries around 79 components.
50% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is Kira by kiibohd.
Parts used alongside the TS3USB30EDGSR
Microcontrollers on boards using the TS3USB30EDGSR
What boards using the TS3USB30EDGSR are built for
TS3USB30EDGSR: common questions
Where can I find a TS3USB30EDGSR reference design?
Each of the 20 boards on this page is a real design using the TS3USB30EDGSR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the TS3USB30EDGSR VCC pin?
The VCC pin has a decoupling capacitor on 8 of 16 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 17 open source designs using the TS3USB30EDGSR.
What pull-up resistor is used on the TS3USB30EDGSR S pin?
The S pin has a pull-up to VDD on 7 of 17 designs, most often 10 kΩ. Counted from the KiCad layouts of 17 open source designs using the TS3USB30EDGSR.
What parts are used alongside the TS3USB30EDGSR?
The 74AHC1G14, FT245RL, TS3A27518E, STM32F405RGT6 and TPS2116DRL appear in the most repositories here.
Which microcontrollers do boards using the TS3USB30EDGSR use?
Most are built on NXP (2), Raspberry Pi (2), RP2040/RP2350 (2) and STM32 (2).
How big is a typical board using the TS3USB30EDGSR?
The median is 73.4 × 84 mm, and 50% are two-layer designs.
What is the most popular open source board using the TS3USB30EDGSR?
By GitHub stars, Kira by kiibohd, with 416 stars.
Can I simulate one of these boards using the TS3USB30EDGSR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.