Power feed manual mill
liorknafo·power-feed-manual-mill·hardware/kicad/power-feed.kicad_pcb
About the Power feed manual mill PCB
Power feed manual mill is an open source RP2040/RP2350 PCB design by liorknafo, published on GitHub. It is a 4-layer board measuring 100 × 100 mm, with 191 components from 74 distinct parts.
Its main chip is the Raspberry Pi RP2040, from the RP2040/RP2350 family. Other key parts include the LM5164DDAR, TMC5160A-TA, W25Q128JVS, STMicroelectronics USBLC6-2SC6 and Diodes AP2112K-3.3TRG1. By type, the board carries 82 resistors, 64 capacitors, 14 diodes, 10 ICs, 8 transistors and 7 connectors.
It belongs with the robotics & motion designs in this gallery.
From the project
DIY stepper power feed for a SIEG X3.5D mill: electromagnetic clutch, RP2040 controller PCB, Rust firmware, build123d CAD
The check: - runs KiCad's ERC and fails on any error not in the reviewed allow-list; - exports the netlist and requires every net to match the intended connections exactly; - lists parts whose footprint is missing.
Every pin gets a short wire stub and a net label; there are no long wires. Connectivity therefore comes only from net names, which keeps the generated schematic correct by construction. Labels used on more than one sheet are global labels; power nets use power symbols.
Main components on the Power feed manual mill
Power feed manual mill bill of materials (BOM)
191 components, 74 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM5164DDAR | HSOP-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.1mm_ThermalVias | U1 |
| 1 | TMC5160A-TA | TQFP-48-1EP_7x7mm_P0.5mm_EP5x5mm_ThermalVias | U2 |
| 1 | Raspberry Pi RP2040 RP2040 | QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm_ThermalVias | U3 |
| 1 | Winbond W25Q128JVSIQ (W25Q16 is out of stock; firmware uses the first 2 MB) W25Q128JVS | SOIC-8_5.3x5.3mm_P1.27mm | U4 |
| 1 | STMicroelectronics USBLC6-2SC6 USBLC6-2SC6 | SOT-23-6 | U5 |
| 1 | Diodes AP2112K-3.3TRG1 AP2112K-3.3 | SOT-23-5 | U6 |
| 1 | SN74LVC1G00DBVR 74LVC1G00 | SOT-23-5 | U7 |
| 2 | SN74AHCT1G08DBVR 74AHCT1G08 | SOT-23-5 | U8, U9 |
| 1 | TLV9061IDBVR TLV9061 | SOT-23-5 | U10 |
| 1 | SQD50P06-15L_GE3 SQD50P06-15L | TO-252-2 | Q1 |
| 1 | AGM60P20R | SOT-223-3_TabPin2 | Q2 |
| 1 | 2N7002 | SOT-23 | Q3 |
| 1 | UMW SI2308A SI2308A | SOT-23 | Q4 |
| 4 | CSD88537ND | SOIC-8_3.9x4.9mm_P1.27mm | Q10, Q11, Q12, Q13 |
| 1 | Abracon ABM8-272-T3 (12 MHz, CL 10 pF, ESR 50R; RPi-approved) 12MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | KF2EDGR-5.08-2P (+ plug KF2EDGK-5.08-2P C440880) 36V IN | PhoenixContact_MSTBA_2,5_2-G-5,08_1x02_P5.08mm_Horizontal | J1 |
| 1 | KF2EDGR-5.08-4P (+ plug KF2EDGK-5.08-4P C440882) MOTOR A+ A- B+ B- | PhoenixContact_MSTBA_2,5_4-G-5,08_1x04_P5.08mm_Horizontal | J2 |
| 1 | 2.54 mm 1x3 male header, hand-solder (Debug Probe's JST-to-0.1in cable) SWD | PinHeader_1x03_P2.54mm_Vertical | J3 |
| 1 | HRO TYPE-C-31-M-12 USB-C | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J4 |
| 1 | KF2EDGR-5.08-2P (+ plug KF2EDGK-5.08-2P C440880) CLUTCH COIL | PhoenixContact_MSTBA_2,5_2-G-5,08_1x02_P5.08mm_Horizontal | J5 |
Show 54 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ZHOURI DC3-2.54-14PAS (2x7 shrouded box header) PANEL 2x7 IDC | IDC-Header_2x07_P2.54mm_Vertical | J6 |
| 1 | JST B7B-XH-A(LF)(SN) JST-XH 7p | JST_XH_B7B-XH-A_1x07_P2.50mm_Vertical | J7 |
| 1 | BLX-A holder + Littelfuse 0215005.MXP (C142718) 5A T 5x20 | Fuseholder_XC_BLX-A_5x20mm_P22.00mm | F1 |
| 1 | Littelfuse 2920L050DR (0.5 A hold, 1 A trip, 60 V) PTC 0.5A/60V | Fuse_2920_7451Metric | F2 |
| 1 | Omron B3S-1000 BOOTSEL | SW_SPST_B3S-1000 | SW1 |
| 1 | Omron B3S-1000 RESET | SW_SPST_B3S-1000 | SW2 |
| 1 | onsemi MMSZ5245BT1G 15V | D_SOD-123 | D1 |
| 1 | SMBJ36A SMBJ36A (TVS) | D_SMB | D2 |
| 2 | KENTO KT-0603G green | LED_0603_1608Metric | D3, D4 |
| 2 | Changjing B5819W SL B5819W | D_SOD-123 | D5, D6 |
| 1 | onsemi MMSZ5242BT1G 12V | D_SOD-123 | D7 |
| 1 | SS210 SS210 (fast decay) | D_SMA | D8 |
| 1 | SS210 SS210 (freewheel) | D_SMA | D9 |
| 1 | XINGLIGHT XL-1608UYC-06 yellow | LED_0603_1608Metric | D10 |
| 4 | USBLC6-4SC6 | SOT-23-6 | D11, D12, D13, D14 |
| 1 | TDK VLS6045EX-470M 47uH | L_TDK_VLS6045EX_VLS6045AF | L1 |
| 2 | Panasonic EEUFR1J471 470uF 63V | CP_Radial_D12.5mm_P5.00mm | C1, C27 |
| 8 | Murata GRM32ER72A225KA35L 2.2uF 100V | C_1210_3225Metric | C2, C3, C4, C20, C22, C24, C26, C50 |
| 1 | FH 0603B222K500NT 2.2nF 50V | C_0603_1608Metric | C5 |
| 1 | Samsung CL10B332KB8NNNC 3.3nF | C_0603_1608Metric | C6 |
| 4 | Samsung CL10C101JB8NNNC 100pF | C_0603_1608Metric | C7, C62, C63, C64 |
| 2 | Samsung CL31A226KAHNNNE 22uF 10V | C_1206_3216Metric | C8, C9 |
| 6 | FH 0603B103K500NT 10nF | C_0603_1608Metric | C10, C53, C57, C58, C59, C60 |
| 3 | Samsung CL21B104KCFNNNE 100nF 100V | C_0805_2012Metric | C11, C12, C14 |
| 1 | Yageo CC0805KRX7R0BB223 22nF 100V | C_0805_2012Metric | C13 |
| 2 | Samsung CL21A475KAQNNNE 4.7uF 10V | C_0805_2012Metric | C15, C45 |
| 1 | Samsung CL10B474KA8NNNC 470nF | C_0603_1608Metric | C16 |
| 1 | Samsung CL31A106KBHNNNE 10uF 25V | C_1206_3216Metric | C17 |
| 22 | Yageo CC0603KRX7R9BB104 100nF | C_0603_1608Metric | C18, C28, C29, C30, C31, C32, C33, C34 +14 |
| 4 | Samsung CL10B224KB8NNNC 220nF 50V | C_0603_1608Metric | C19, C21, C23, C25 |
| 3 | Samsung CL10A105KB8NNNC 1uF | C_0603_1608Metric | C36, C37, C44 |
| 2 | Samsung CL10C150JB8NNNC 15pF | C_0603_1608Metric | C42, C43 |
| 1 | Samsung CL10B102KB8NNNC 1nF | C_0603_1608Metric | C51 |
| 2 | UNI-ROYAL 0603WAF2202T5E 22k | R_0603_1608Metric | R1, R52 |
| 1 | FOJAN FRC0603F4122TS 41.2k | R_0603_1608Metric | R2 |
| 7 | UNI-ROYAL 0603WAF1003T5E 100k | R_0603_1608Metric | R3, R7, R40, R41, R42, R46, R50 |
| 1 | UNI-ROYAL 0603WAF3162T5E 31.6k | R_0603_1608Metric | R4 |
| 2 | UNI-ROYAL 0603WAF2003T5E 200k | R_0603_1608Metric | R5, R54 |
| 1 | UNI-ROYAL 0603WAF4701T5E 4.7k | R_0603_1608Metric | R6 |
| 1 | UNI-ROYAL 0603WAF7501T5E 7.5k | R_0603_1608Metric | R8 |
| 1 | UNI-ROYAL 0603WAF220KT5E 2.2 | R_0603_1608Metric | R9 |
| 8 | UNI-ROYAL 0402WGF470KTCE 4.7 | R_0402_1005Metric | R10, R11, R12, R13, R14, R15, R16, R17 |
| 2 | CSM2512FT50L0 0.05 1% 3W | R_2512_6332Metric | R18, R21 |
| 4 | UNI-ROYAL 0603WAF470JT5E 47 | R_0603_1608Metric | R19, R20, R22, R23 |
| 17 | UNI-ROYAL 0603WAF1002T5E 10k | R_0603_1608Metric | R24, R27, R37, R38, R39, R45, R55, R57 +9 |
| 14 | UNI-ROYAL 0603WAF1001T5E 1k | R_0603_1608Metric | R25, R26, R28, R44, R53, R56, R58, R60 +6 |
| 2 | UNI-ROYAL 0603WAF5101T5E 5.1k | R_0603_1608Metric | R29, R30 |
| 2 | UNI-ROYAL 0603WAF270JT5E 27 | R_0603_1608Metric | R31, R32 |
| 4 | UNI-ROYAL 0603WAF330JT5E 33 | R_0603_1608Metric | R33, R34, R35, R36 |
| 1 | UNI-ROYAL 0603WAF3300T5E 330 | R_0603_1608Metric | R43 |
| 4 | UNI-ROYAL 0603WAF2201T5E 2.2k | R_0603_1608Metric | R47, R73, R75, R77 |
| 1 | UNI-ROYAL 1206W4F4701T5E 4.7k | R_1206_3216Metric | R48 |
| 6 | UNI-ROYAL 0603WAF1000T5E 100 | R_0603_1608Metric | R49, R74, R76, R78, R81, R82 |
| 1 | FOJAN FRM121WFR100TM 0.1 1% 1W | R_1206_3216Metric | R51 |
Power feed manual mill design files
The KiCad project lives in the liorknafo/power-feed-manual-mill repository on GitHub; these links point at the commit this page was built from.
Power feed manual mill: common questions
What microcontroller does the Power feed manual mill use?
The Power feed manual mill is built around the Raspberry Pi RP2040, from the RP2040/RP2350 family.
How big is the Power feed manual mill PCB?
The Power feed manual mill measures 100 × 100 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Power feed manual mill?
191 components, from 74 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Power feed manual mill design files?
From the liorknafo/power-feed-manual-mill repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Power feed manual mill design in my own project?
The repository has no license, so all rights stay with liorknafo. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Power feed manual mill without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.
Similar boards
RP2040/RP2350
OSO-BOOK-C1
joeycastillo
85 × 115 mm29 parts2LCC-BY-SA-4.08.1kRP2040/RP2350
Corne cherry
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
Corne chocolate
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
Jitx design
gusmanb
55.5 × 65 mm26 parts4LGPL-3.05.0kRP2040/RP2350
LogicAnalyzer
gusmanb
57 × 55.2 mm6 parts2LGPL-3.05.0kRP2040/RP2350
Main
google
98 × 71 mm102 parts2LApache-2.02.9k