IRQ-TestHarness
About the IRQ-TestHarness PCB
IRQ-TestHarness is an open source PCB design by Manuvr, published on GitHub. It is a 4-layer board measuring 20.9 × 44.7 mm, with 22 components from 7 distinct parts.
Other key parts include the 74HC165. By type, the board carries 12 switches, 2 ICs and 2 connectors.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
KiCAD source files for Manuvr's motion capture glove.
. , . . | \ -+- .| . .|. .. |/|(]| | (][)(||(|[ | ) ._|
Hardware source files for Manuvr's motion capture glove.
Project | Purpose :-----|:------ Digitabulum-r2 | Sensor front-end PCB. (Pending release) r2-Metacarpals | Flex circuit for the metacarpals. (Pending release) r2-Digit | Flex circuit for digits. (Pending release) r2-Backplane | A backplane PCB containing the power-management block and associated support circuits. Compute-WROOM32 | A digitabulum compute PCB based on Espressif's WROOM32 module.
Main components on the IRQ-TestHarness
IRQ-TestHarness bill of materials (BOM)
22 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 74HC165 | DHVQFN16-3.5x2.5 | U2, U3 |
| 1 | CONN_01X05 | Pin_Header_Straight_1x05_Pitch2.54mm | P1 |
| 1 | CONN_01X05 | Pin_Header_Straight_1x05_Pitch1.27mm | P2 |
| 1 | CAPARRAY_4 | CapArray_CKCL44 | CARY1 |
| 4 | R_PACK4 | RES_4_EXBN8V | RP1, RP2, RP3, RP5 |
| 1 | R_PACK4 | SW_DIP_x4_W5.08mm_Slide_Copal_CHS-A | RP4 |
| 12 | SW_PUSH_SMALL_H | SW_SPST_Panasonic_EVQPL_3PL_5PL_PT_A15 | SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8 +4 |
IRQ-TestHarness design files
The KiCad project lives in the Manuvr/Digitabulum-Hardware repository on GitHub; these links point at the commit this page was built from.
IRQ-TestHarness: common questions
How big is the IRQ-TestHarness PCB?
The IRQ-TestHarness measures 20.9 × 44.7 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the IRQ-TestHarness?
22 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the IRQ-TestHarness design files?
From the Manuvr/Digitabulum-Hardware repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the IRQ-TestHarness design in my own project?
The repository has no license, so all rights stay with Manuvr. Use it as a reference, and ask the author before reusing the design.
More boards in Digitabulum-Hardware
R2-Backplane
24.8 × 67.1 mm41 parts4LNo license4
PowerPlant-Module
22.5 × 37.7 mm35 parts4LNo license4
R2-Dev-Backplane
77.9 × 67.1 mm33 parts4LNo license4
ESP32WROOM32 Compute
24.8 × 31.7 mm15 parts4LNo license4
LevelShifter
14.9 × 37.7 mm7 parts4LNo license4
Compute PCB Template
24.8 × 27.2 mm6 parts4LNo license4
Digitabulum Test Harness
24.8 × 33.1 mm4 parts4LNo license4
Similar boards
88 Pin Vag Breakout
rusefi
142 × 58 mm91 parts2LGPL-3.01.2k
134pin 7-967288-1
139.7 × 73.7 mm38 parts2LGPL-3.01.2k
Breakout 60pin EEC-IV
139.7 × 62.2 mm15 parts2LGPL-3.01.2k
Breakout 112pin Connector
174 × 58 mm39 parts2LGPL-3.01.2k
Eecv breakout
140.8 × 53.7 mm9 parts4LGPL-3.01.2k
Rj45 breakout
rene-dev
15.2 × 53.8 mm3 parts2LGPL-3.0979