E ink dashboard
Nxyz-natan·e-ink-dashboard·kicad/e-ink dashboard.kicad_pcb
About the E ink dashboard PCB
E ink dashboard is an open source ESP32 PCB design by Nxyz-natan, published on GitHub. It is a 2-layer board measuring 69.6 × 94.2 mm, with 20 components from 14 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the BME280, ME6211C33M5 and TP4056-42-ESOP8. By type, the board carries 6 resistors, 5 capacitors, 4 ICs, 3 connectors and 2 switches.
It belongs with the displays & leds, power & battery and sensors designs in this gallery.
From the project
I designed a custom PCB that integrates: ESP32-S3 microcontroller BME280 sensor Power management (voltage regulator + charging IC) USB-C input Display connector
I designed a custom PCB that integrates: ESP32-S3 microcontroller BME280 sensor Power management (voltage regulator + charging IC) USB-C input Display connector
Real-time weather display displays whats spotify playing Room temperature and humidity using BME280 sensor Calendar, date, and time display Low power consumption using e-ink technology
here is my schematics here my pcb here is my case ## Bill of Materials
Main components on the E ink dashboard
E ink dashboard bill of materials (BOM)
20 components, 14 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | BME280 | Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumbering | U2 |
| 1 | ME6211C33M5 | SOT-23-5 | U3 |
| 1 | TP4056-42-ESOP8 | SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm_ThermalVias | U4 |
| 1 | Conn_01x02 | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J1 |
| 1 | Conn_01x08 | PinSocket_1x08_P2.54mm_Vertical | J2 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J3 |
| 2 | SW_Push | SW_Push_1TS009xxxx-xxxx-xxxx_6x6x5mm | SW1, SW2 |
| 3 | 10 µF | C_0805_2012Metric | C1, C2, C5 |
| 2 | 0.1 µF | C_0805_2012Metric | C3, C4 |
| 2 | 5.1 kΩ | R_0805_2012Metric | R1, R2 |
| 1 | 1.2 kΩ | R_0805_2012Metric | R3 |
| 1 | 10 kΩ | R_0805_2012Metric | R4 |
| 2 | 4.7 kΩ | R_0805_2012Metric | R5, R6 |
E ink dashboard design files
The KiCad project lives in the Nxyz-natan/e-ink-dashboard repository on GitHub; these links point at the commit this page was built from.
E ink dashboard: common questions
What microcontroller does the E ink dashboard use?
The E ink dashboard is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the E ink dashboard PCB?
The E ink dashboard measures 69.6 × 94.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the E ink dashboard?
20 components, from 14 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the E ink dashboard design files?
From the Nxyz-natan/e-ink-dashboard repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the E ink dashboard design in my own project?
The repository has no license, so all rights stay with Nxyz-natan. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the E ink dashboard without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k