Charlieplex 3x3

rjwalters·kicad-tools·boards/02-charlieplex-led/output/charlieplex_3x3.kicad_pcb

Charlieplex 3x3 PCB layout, top view — open source AVR/Arduino board by rjwalters

About the Charlieplex 3x3 PCB

Charlieplex 3x3 is an open source AVR/Arduino PCB design by rjwalters, published on GitHub under the MIT license. It is a 2-layer board measuring 50 × 55 mm, with 19 components from 8 distinct parts.

Its main chip is the ATTINY85-20PU, from the AVR/Arduino family. By type, the board carries 9 diodes, 5 resistors, 2 connectors, 2 capacitors and 1 IC.

From the project

Standalone Python tools for parsing and manipulating KiCad schematic and PCB files

A working 3 × 3 red LED sequencer built around a real ATtiny85-20PU. Four GPIO pins drive nine LEDs through four 330 Ω resistors. The 50 × 55 mm, two-layer board includes regulated 3.3–5 V power input, supply decoupling, reset pullup, and a standard six-pin AVR ISP header.

See HARDWARE.md for the complete pinout, verified component identities, power instructions and firmware programming. U1, J1 and J2 are hand-soldered after the sixteen SMT components are assembled. The supplied firmware advances through D1–D9; physical hardware testing has not yet been performed.

Main components on the Charlieplex 3x3

Charlieplex 3x3 bill of materials (BOM)

19 components, 8 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ATTINY85-20PU
ATtiny85-20PU
U1
1
C7501260
POWER
J1
1
C65114
AVR-ISP
J2
9
LED
D1, D2, D3, D4, D5, D6, D7, D8 +1
1
100NF
100nF
C1
1
4.7UF
4.7uF
C2
4
330R
R1, R2, R3, R4
1
10K
10k
R5

Charlieplex 3x3 design files

The KiCad project lives in the rjwalters/kicad-tools repository on GitHub; these links point at the commit this page was built from.

Charlieplex 3x3: common questions

What microcontroller does the Charlieplex 3x3 use?

The Charlieplex 3x3 is built around the ATTINY85-20PU, from the AVR/Arduino family.

How big is the Charlieplex 3x3 PCB?

The Charlieplex 3x3 measures 50 × 55 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Charlieplex 3x3?

19 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Charlieplex 3x3 design files?

From the rjwalters/kicad-tools repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Charlieplex 3x3 design in my own project?

Yes, under the terms of its MIT license, which rjwalters chose for the repository.

Can I test firmware for the Charlieplex 3x3 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in kicad-tools

Similar boards