Usb joystick routed
rjwalters·kicad-tools·boards/03-usb-joystick/output/usb_joystick_routed.kicad_pcb
About the Usb joystick routed PCB
Usb joystick routed is an open source AVR/Arduino PCB design by rjwalters, published on GitHub under the MIT license. It is a 4-layer board measuring 80 × 60 mm, with 38 components from 17 distinct parts.
Its main chip is the ATMEGA32U4-AU, from the AVR/Arduino family. Other key parts include the USBLC6-2SC6. By type, the board carries 13 capacitors, 13 resistors, 5 switches, 3 connectors, 2 ICs and 1 crystal.
From the project
Standalone Python tools for parsing and manipulating KiCad schematic and PCB files
Real ATmega32U4-AU USB HID controller hardware: USB-C bus power and ESD, 8MHz crystal, reset/HWB support, AVR ISP, two filtered joystick axes and four buttons plus a joystick switch. The MCU uses the actual TQFP-44 pinout.
Revision A was a routing fixture with a fictitious 32-pin MCU mapping. Its saved routing and manufacturing outputs are not valid evidence for revision B. See DESIGN_REVIEW.md for primary sources, exact interface pinouts, bring-up requirements, and remaining release checks.
Main components on the Usb joystick routed
Usb joystick routed bill of materials (BOM)
38 components, 17 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATMEGA32U4-AU Microchip | TQFP-44_10x10mm_P0.8mm | U1 |
| 1 | USBLC6-2SC6 STMicroelectronics | SOT-23-6 | U2 |
| 1 | ECS-80-12-33-JGN 8MHz ECS | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | USB4085-GF-A GCT | USB_C_Receptacle_GCT_USB4085 | J1 |
| 1 | Joystick 5V X Y SW JST | JST_PH_S5B-PH-SM4-TB_1x05-1MP_P2.00mm_Horizontal | J2 |
| 1 | TSM-103-01-T-DV-P AVR ISP Samtec | Samtec_TSM-103-01-T-DV | J3 |
| 1 | 1206L035/16YR 350mA Littelfuse | Fuse_1206_3216Metric | F1 |
| 5 | TL3342F160QG E-Switch | SW_SPST_TL3342 | SW1, SW2, SW3, SW4, SW5 |
| 7 | GRM188R71C104KA01D 100nF Murata | C_0603_1608Metric | C1, C2, C3, C4, C5, C7, C13 |
| 1 | GRM188R71A105KA61D 1uF Murata | C_0603_1608Metric | C6 |
| 2 | GRM1885C1H150JA01D 15pF Murata | C_0603_1608Metric | C8, C9 |
| 2 | GRM188R71H103KA01D 10nF Murata | C_0603_1608Metric | C10, C11 |
| 1 | GRM188R61A475KE15D 4.7uF Murata | C_0603_1608Metric | C12 |
| 2 | RC0603FR-075K1L 5.1k Yageo | R_0603_1608Metric | R1, R2 |
| 2 | RC0402FR-0722RL 22 Yageo | R_0402_1005Metric | R3, R4 |
| 7 | RC0603FR-0710KL 10k Yageo | R_0603_1608Metric | R5, R6, R12, R13, R14, R15, R16 |
| 2 | RC0603FR-071KL 1k Yageo | R_0603_1608Metric | R10, R11 |
Usb joystick routed design files
The KiCad project lives in the rjwalters/kicad-tools repository on GitHub; these links point at the commit this page was built from.
Usb joystick routed: common questions
What microcontroller does the Usb joystick routed use?
The Usb joystick routed is built around the ATMEGA32U4-AU, from the AVR/Arduino family.
How big is the Usb joystick routed PCB?
The Usb joystick routed measures 80 × 60 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Usb joystick routed?
38 components, from 17 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Usb joystick routed design files?
From the rjwalters/kicad-tools repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Usb joystick routed design in my own project?
Yes, under the terms of its MIT license, which rjwalters chose for the repository.
Can I test firmware for the Usb joystick routed without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in kicad-tools
USB-C PD 5V supply — development
rjwalters
100 × 65 mm47 parts4LMIT74STM32
Matchgroup test routed
rjwalters
100 × 80 mm43 parts6LMIT74STM32
Matchgroup test
rjwalters
100 × 80 mm43 parts6LMIT74AVR/Arduino
Bldc controller routed
rjwalters
70 × 90 mm42 parts4LMIT74AVR/Arduino
Bldc controller
rjwalters
70 × 90 mm42 parts4LMIT74AVR/Arduino
Usb joystick
rjwalters
80 × 60 mm38 parts4LMIT74Diffpair test routed
rjwalters
90 × 70 mm36 parts4LMIT74Diffpair test
rjwalters
90 × 70 mm36 parts4LMIT74AVR/Arduino
Charlieplex 3x3 routed
rjwalters
50 × 55 mm19 parts2LMIT74AVR/Arduino
Charlieplex 3x3
rjwalters
50 × 55 mm19 parts2LMIT74STM32
Stm32 devboard routed
rjwalters
60 × 40 mm17 parts2LMIT74
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k