ESP32C3 Slave N-CH
RoboDurden·Esp32_20A_80V_dcdc·KiCad PCB v2/ESP32C3_Slave_N-CH.kicad_pcb
About the ESP32C3 Slave N-CH PCB
ESP32C3 Slave N-CH is an open source ESP32 PCB design by RoboDurden, published on GitHub under the MIT license. It is a 2-layer board measuring 80 × 33 mm, with 23 components from 19 distinct parts.
Its main chip is the ESP32_C3_Super_Mini, from the ESP32 family. Other key parts include the 128x64, B0515S and EG2104. By type, the board carries 8 connectors, 6 ICs, 4 resistors, 3 capacitors and 2 transistors.
It belongs with the displays & leds, power & battery and iot & wireless designs in this gallery.
From the project
20A 80V dcdc/mppt with Esp32 and touch display
$2 pcb order at JLPCB ("Add gerber file" upload button): https://github.com/RoboDurden/Esp3220A80Vdcdc/blob/main/KiCad%20PCB%20v2/production/Esp20A80V2024-05-12_13-24-33/Esp20A80V.zip
All GPIO pins to alternative headers. All headers on 2.54mm grid for prototyping board.
PCB and S2Mini are cheap, so simply solder S2Mini to backside. The tin solder should quickly be sucked into the holes of the S2_Mini and connect to the holes of the pcb :-)

Main components on the ESP32C3 Slave N-CH
ESP32C3 Slave N-CH bill of materials (BOM)
23 components, 19 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 128x64 | 128x64OLED | U1, U3 |
| 1 | B0515S | B0515S | U2 |
| 1 | ESP32_C3_Super_Mini | ESP32_C3_Super_Mini | U4 |
| 2 | EG2104 | SOP-8_3.76x4.96mm_P1.27mm | U5, U6 |
| 1 | SI2300 IRF3206 | TO-263-2_holes | Q1 |
| 1 | SI2305 IRF3206 | TO-263-2_holes | Q2 |
| 2 | I2C | JST_EH_S4B-EH_1x04_P2.50mm_Horizontal | J1, J2 |
| 1 | I2C/UART SPI | PinSocket_2x05_P2.54mm_Vertical | J3 |
| 1 | In V+ | SolderWire-2sqmm_1x01_D2mm_OD3.9mm | J4 |
| 1 | Out1 | SolderWire-2sqmm_1x01_D2mm_OD3.9mm | J5 |
| 1 | Out2 | SolderWire-2sqmm_1x01_D2mm_OD3.9mm | J6 |
| 2 | mount | PinSocket_1x02_P2.54mm_Vertical | J7, J8 |
| 1 | 220NF 4,7μF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1 |
| 1 | 220NF 0,1μF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2 |
| 1 | 1μF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3 |
| 1 | 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 3.9K 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 1 | 10 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
| 1 | 3.9K 10 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
ESP32C3 Slave N-CH design files
The KiCad project lives in the RoboDurden/Esp32_20A_80V_dcdc repository on GitHub; these links point at the commit this page was built from.
ESP32C3 Slave N-CH: common questions
What microcontroller does the ESP32C3 Slave N-CH use?
The ESP32C3 Slave N-CH is built around the ESP32_C3_Super_Mini, from the ESP32 family.
How big is the ESP32C3 Slave N-CH PCB?
The ESP32C3 Slave N-CH measures 80 × 33 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ESP32C3 Slave N-CH?
23 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the ESP32C3 Slave N-CH design files?
From the RoboDurden/Esp32_20A_80V_dcdc repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the ESP32C3 Slave N-CH design in my own project?
Yes, under the terms of its MIT license, which RoboDurden chose for the repository.
Can I test firmware for the ESP32C3 Slave N-CH without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Esp32_20A_80V_dcdc
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k